background image

7

 Press 

the    key to return to the main screen.

• 

When the alarm ceases  press the 

 Key to start the unit.

1.8. Alarm 

list

Cod

Description

Type of restoring

A01

Environment probe failure

Manual

A05

Oil level alarm

Only display

A06

Air fi lter alarm

Only display

A07

Water temperature alarm

Manual

A08

Microdoor

Automatic

A09

Open door

Automatic

A10

Oil pressure alarm

Manual

A11

Maximumm pressostat alarm

Automatic

A12

High temperature alarm

Only display

A13

Low temperature alarm

Only display

A14

Thermal protection

Automatic

A15

Low battery level

Manual

A16

Start failed

Manual

A17

Alternator failure

Manual

A18

Pre-heat water probe failure

Only display

1.9. Alarm 

description

A01 Enviroment probe failure alarm
This alarm causes the machine to stop permanently until the failure is repaired. To re-start the machine, you should 
reset alarm following procedure described in the above-mentioned paragraph and press the on/off  

 key.

A04/11 Pressostat alarm
It occurs for a maximum or minimum pressostat intervention. The causes for the intervention of the maximum presso-
stat may be due to an inappropriate cleaning of the condenser or a slackening of the condenser fan belts, The inter-
vention of the minimum pressostat may be due to Freon leakage. The intervention produces the machine stop until 
the alarm disappears.
A05 Oil level alarm
It is an only signalling alarm which does not affect the machine operation
A06 Air fi lter alarm
It is an only signalling alarm which does not affect the machine operation
A07 Water temperature alarm
It occurs when the radiator water temperature exceed the allowed value. It causes the diesel motor to stop. To re-
start the machine you should reset the alarm following the procedure described in the above-mentioned paragraph 
and press the on/off 

 key.

Summary of Contents for DFZ

















Reviews: