background image

APPLiCAtioN

CooPERAtioN AND oPERAtiNG RANGE

transmitter RoB-01/12-24V transmitter RoB-01/12-24V

RNK-02

200 

m

RNP-02 

180 

m

RNK-04

200 

m

RNL-01

180 

m

P-256/8

250 

m

RTN-01

200 

m

P-257/4 (2)

200 

m

RCR-01

180 

m

RNM-10

250 

m

RTI-01

180 

m

RNP-01

180 

m

RXM-01 

250 

m

CAutioN! the given range concerns open area - an ide-

al  condition  without  any  natural  or  artificial  obstacles.  

If there are some obstacles between a transmitter and a re-

ceiver, it is advisable to decrease the range according to:

wood and  plaster: from 5 to 20 %, bricks: from 10 to 40 %,

reinforced concrete: from 40 to 80 %, 

metal: from 90 to 100%, glass: from 10 to 20 %

over- and underground medium and high electrical pow-

er lines, radio and television transmitters, GSM transmit-

ters set close to a device system have also a negative 

influence on the range.

ROB-01/12-24V device 

can be controlled by 

means of any transmitter 

of EXTA FREE system. 

In this application 

P-256/8 remote control 

was used which can 

control external lighting 

(ROP-01), roller blinds 

and a garage gate 

(SRP-02).

CoNNECtioN

MouNtiNG, FuNCtioNiNG

1. Disconnect power supply by the phase fuse, the circuit-breaker or the 

switch-disconnector combined to the proper circuit.

2. Check  if  there  is  no  voltage  on  connection  cables  by  means  of  

a special measure equipment.

3. Connect the cables to ROB-01/12-24V device terminals in accordance 

with the installing diagram.

4. Switch on the power supply from the mains.

The ROB-01/12-24V device should be mounted in the connection place 

of manual gate drive release. The receiver operates in impulse mode - af-

ter receiving a signal from a programmed transmitter it short circuits relay 

output terminals (11-14) for about 0,5 seconds. 

To improve device operation range it is possi-

ble to connect an additional external antenna to 

ANT terminal. A connecting cable of maximum 

section 2,5 mm

2

 can be the antenna.

12 ÷ 24 V 

~/

~/+

~/–

EXISTING

GATE

CONTROLLER

REMotE CoNtRoL DELEtioN

Press PROG push-button of ROB-01 device 

for a longer time.

After 5 seconds LED red diode switches on 

(signal pulsates) and then it switches off.

Release the push-button in ROB-01  

- MEMORY IS DELETED. 

REMotE CoNtRoLS PRoGRAMMiNG

Press the transmitter’s push-button  

for a longer time. LED red diode switches on 

(first signal pulsates, next the signal is constant).

Release the transmitter’s push-button. 

LED red diode switches on (signal 

pulsates) and then switches off  

- THE TRANSMITTER IS ADDED.

Press PROG push-button of ROB-01 device  

for a longer time till LED red diode switches on 

(constant signal). Next release PROG push-button. 

An exemplary programming procedure with the use of P-257/2 remote controller. The procedure for the rest of radio EXTA FREE transmitters 

is analogous. 

CAUTION: Every transmitter can cooperate with ROB-01 in a different mode, depending on how they were added to 

the device. One transmitter can be added during one programming cycle. Full memory is signalled with pulsating LED red diode.

WARRANtY CARD

There is 24 months guarantee on the product

1.  ZAMEL provides a two-year warranty for its products. 

2.  The ZAMEL warranty does not cover: a) mechanical defects resulting from transport, loading / unloading or other circumstances  

b) defects resulting from incorrect installation or operation of ZAMEL products; c) defects resulting from any changes made by CUS-

TOMERS or third parties, to products sold or equipment necessary for the correct operation of products sold; d) defects resulting 

from force majeure or other aleatory events for which ZAMEL is not liable; e) power supply (batteries) to be equipped with a device 

in the moment of sale (if they appear); 

3.  All complaints in relation to the warranty must be provided by the CUSTOMER in writing to the retailer after discovering a defect.; 

4.  ZAMEL will review complaints in accordance with existing regulations.; 

5.  The way a complaint is settled, e.g. replacement of the product, repair or refund, is left to the discretion of ZAMEL. 

6.  Guarantee does not exclude, does not limit, nor does it suspend the rights of the PURCHASER resulting from the discrepancy 

between the goods and the contract.

Salesman stamp and signature, date of sale

Reviews: