RADIO TRANSMITTERS PROGRAMMING
TIME PROGRAMMING
RADIO TRANSMITTERS DELETION
BISTABLE mode:
SWITCH ON/SWITCH OFF mode (two push-buttons):
TIME mode (one push-button):
An exemplary programming procedure with the use of P-257/2 remote control. The
procedure for the rest of radio EXTA FREE transmitters is analogous. CAUTION: Every
transmitter can cooperate with SLR-01 in a different mode, depending on how they
were added to the device. One transmitter can be added during one programming
cycle. Full memory is signalled with pulsating LED red diode.
Press the transmitter’s
push-button for a longer
time. LED red diode
switches on (first signal
pulsates, next the signal is
constant)
Press and release
transmitter’s push-button.
LED red diode switches on
(first the signal pulsates,
next the signal is constant)
Press and release the first
transmitter’s push-button.
LED red diode switches on
(first the signal pulsates,
next the signal is constant)
Press and release the same
transmitter’s push-button.
LED red diode switches on
(the signal pulsates) and
next it switches off - THE
TRANSMITTER IS ADDED
Press and release the
same transmitter’s
push-button. LED red
diode switches on (the
signal pulsates) and
next it switches off - THE
TRANSMITTER IS ADDED
Press and release the
second transmitter’s
push-button. LED red
diode switches on (the
signal pulsates) and
next it switches off - THE
TRANSMITTER IS ADDED
Press PROG push-button of
SLR-01 device for a longer time
until LED red diode switches on
(constant signal). Next release
PROG push-button
Press PROG push-button of
SLR-01 device for a longer time
until LED red diode switches on
(constant signal). Next release
PROG push-button
Press PROG push-button of
SLR-01 device for a longer time
until LED red diode switches on
(constant signal). Next release
PROG push-button
Maximum time is 18 hours.
Press PROG push-button of SLR-01
device for a longer time till LED red
diode switches on (constant signal).
Next release the PROG push-button.
Wait (for about 5 seconds) till LED
red diode switches on (first signal
pulsates, next the signal is constant)
After the adjusted
time is reached (the
number of LED red
diode flashes) press
PROG push-button
and then release it
- TIME IS ADDED
Press PROG push-button
of SLR-01 device and
then release it. LED red
diode switches off and
then switches on (signal
pulsates). Every LED diode
pulse equals 1 second
Press PROG push-button
of SLR-01 device for a
longer time.
After 5 seconds LED red
diode switches on (the
signal pulsates) and then it
switches off.
Release the push-button
in SLR-01 - MEMORY IS
DELETED.
OPERATION TABLE
Symb
ol
RNK
-02
RNK
-04
P-256/8
P-257/2
P-257/4
RNM
-10
RNP
-01
RNP
-02
RNL
-01
RTN-01
RCR-01
RTI-01
RXM
-01
P-260
SLR-01
180 180 230 180 180 230 160 160 160 200 160 160 230
-
CAUTION: The given range concerns open area - an ideal condition without any natural
or artificial obstacles. If there are some obstacles between a transmitter and a receiver,
it is advisable to decrease the range according to: bricks: from 10 to 40 %, wood and
plaster: from 5 to 20 %, reinforced concrete: from 40 to 80 %, metal: from 90 to 100%
, glass: from 10 to 20 %. Over- and underground medium and high electrical power
lines, radio and television transmitters, GSM transmitters set close to a device system
have also a negative influence on the range.
1 s 2 s n s