manualshive.com logo in svg

Z3 Technology Z3Cam-DX, User Instructions

Share
Download
Z3 Technology Z3Cam-DX User Instructions Download Page 50

 
 

 

 

Z3Cam-DX User Instructions

 

 

 

DOC-USR-0152-04

 

 

 

___________________________________________________________________________________________ 

Z3 Technology, LLC 

♦

 100 N 8

th

 ST, STE 250 

♦

 Lincoln, NE 68508-1369 USA 

♦

 +1.402.323.0702 

50 

If you do not have camera control software it is possible to write your own. An example application for 

sending VISCA commands from a Windows PC to the Z3Cam-DX has been provided in APPENDIX C:  Example 

Camera Controller Application. 

 

7.5

 

ONVIF

 Profile S 

Z3Cam-DX software is compliant with ONVIF Profile S.

 3

   

ONVIF is enabled by default. ONVIF Clients should be able to discover the Z3Cam-DX using WS-

Discovery. 

 

(1)

 

Open your ONVIF client program. 

(2)

 

Use ONVIF device discovery to find the Z3Cam-DX on the network. 

Note:  

For manual discovery of ONVIF, use the Z3Cam-DX IP address and the port 

8080

 as shown in the following 

URL example:  http://192.168.0.120:8080/onvif/device_service 

(3)

 

Enter your valid user ID and password. 

Note:  

If you are logging onto the camera for the first time, the default user ID is 

admin

 and the default 

password is 

admin

. 

7.6

 

ONVIF

 Fixed Profile Support 

This section reflects changes for software version 2.36b or newer.

  

By default, this Z3 device supports 2 fixed profiles for each Camera (Channel), this allows VMS/NVRs' too 

see both cameras within a single driver when using ONVIF. 

There may be a situation where only one camera is desired to be seen by an ONVIF VMS/NVR. This can be 

achieved by going to the 

System Setup

 tab and clicking on o 

Advanced Settings

; The clicking on 

Configure 

ONVIF

 within the 

Device Management

 section of the 

System Setup

 tab. 

                                            

3

 ONVIF promotes standardized interfaces for interoperability of IP-based security products. For more information, 

visit 

www.onvif.org

.  

Summary of Contents for Z3Cam-DX






























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands