background image

Basic (version 1)

Battery (version 1)

Wake Up (version 2)

Association (version 2)

Version (version 1)

Multi Channel (version 3)

Multi Channel Association (version 2)

Configuration (version 1)

Manufacturer Specific (version 1)

Protection (version 1)

Node Naming and Location (version 1)

Multilevel Switch (version 1)

Scene Activation (version 1)

All Switch (version 1)

Scene Controller Configuration (version 1)

Controlled Command Classes

Basic (version 1)

Multi Channel (version 3)

Multilevel Switch (version 1)

Scene Activation (version 1)

All Switch (version 1)

Technical Data

IP Rating

IP 20

Battery Type

1 * CR2032

Frequency

868.42 MHz (SRD Band)

Wireless Range

up to 100 m outside, on average up to 20 m inside buildings

Explorer Frame Support Yes

SDK

4.54 pl1

Device Type

Slave with routing capabilities

Generic Device Class

Remote Switch

Specific Device Class

Multilevel Remote Switch

Routing

No

FLiRS

No

Firmware Version

1.2

Explanation of Z-Wave specific terms

(c) 2012 Z-Wave Europe GmbH, Goldbachstr. 13, 09337 Hohenstein-Ernstthal, Germany, All rights reserved, www.zwaveeurope.com - pp 12 

Summary of Contents for ZME WCS1














Reviews: