background image

24

ERROR CODES

LEr (Low Temperature Alarm )

Grill temperature was below 120

for more than 20 minutes.

HEr (High Temperature Alarm )

Grill temperature reached 550

.

Er 1

Ensure temperature probe is properly connected to the controller board.

Er 2

Temperature dial security alarm.

Turn the Temperature dial to SHUT DOWN CYCLE, turn off the grill and then turn it on.

Then you can turn the Temperature Dial to any cooking temperature desired.

WARNING: DO NOT TURN OFF THE SWITCH WHILE THE FAN IS STILL WORKING ON

THE SHUT DOWN CYCLE, THE GRILL WILL AUTOMATICALLY SHUT OFF WHEN THE

CYCLE IS DONE. INTERRUPTION OF THE SHUT DOWN CYCLE COULD RESULT IN A

FIRE IN THE HOPPER CHAMBER.

Unexpected grill temperature is

displayed

External Factor

Grill temperature is influenced by

environmental factors such as high

temperature, wind and direct sun.

Place unit in shaded area. Open the lid

to reduce inside temperature. After

start your grill in 40 minutes, the grill

will reach your desired temperature.

Excess or discolored smoke

Pellets

Replace moist pellets with fresh dry

pellets.

Get your new parts

Contact

Z GRILLS

Customer

Service or your

Z GRILLS

dealer to place

an order

When contacting customer support

please have the following information

available: Your authorized Z Grills

dealer, your name, phone number,

address, your Z Grill serial number and

part identification number. Your part

number is listed on the COMPONENT

LIST.

Summary of Contents for ZPG-700D2






























Reviews: