14
Starting your vehicle with the PIN Lock active:
1.
A 40-second countdown will begin, displayed on the cluster.
2.
The dashboard turn signal indicators will flash and blink
3. At 10 seconds, a “Keyfob Not Detected” warning will
display on the cluster, accompanied by an audible chime,
as a final reminder to enter your PIN.
4. If PIN Pedal is enabled, at 5 seconds, the gas pedal will be disabled.
5.
At 0 seconds, the PIN Lock will trigger.
Entering your PIN:
1.
Enter your pin before the countdown ends and before
shifting out of Park to disarm PIN Lock and begin
operating the vehicle.
2.
Enter your pin while the PIN Lock is already triggered to
disarm the PIN Lock and begin operating the vehicle.
3. If you make a mistake, pause for two full seconds or
press
CRUISE On/Off
to start over.
The symbols described previously will appear on the cluster
to indicate the buttons you’ve pressed. Once the correct PIN
is entered, the cluster will display
“PIN Unlocked.”
What happens when PIN Lock is triggered?:
If PIN Brakes, Horn, Lights and Pedal are enabled:
1. A Light Show will begin.
2.
The horn will honk in a random pattern.
3. All four brakes will lock up.
4. The gas pedal will be disabled.
These individual measures can be enabled or disabled
using their respective PIN Lock Menu options.
What triggers the PIN Lock?:
1.
failure to enter your PIN before the PIN countdown ends
2. shifting out of Park before the PIN countdown ends (from
vehicle start)
3. whenever the vehicle is stops with a carjacking in
progress (from Carjack Mode, see below)
Carjack Mode:
With a PIN set and enabled, when the vehicle is running
and you leave the vehicle with the key and close the door
,
Carjack Mode will be initiated.
1.
Once the vehicle starts moving again, a 20-second PIN
countdown will begin.
2.
At 10 seconds, a “Keyfob Not Detected” warning will
display on the cluster, accompanied by an audible chime,
as a final reminder to enter your PIN.
3. At 5 seconds, the gas pedal will be disabled.
4. Once the vehicle comes to a stop, PIN Lock is triggered
.
5.
Enter the PIN at any point during this process to unlock
the vehicle and return to normal operation.
Note:
If enabled alongside PIN Lock, there will be an audible
chime and “Keyfob not Detected” message on the dash
every time the driver door is opened as a reminder that
Carjack mode will be inititated if you exit the running vehicle
with the key.
Customizing PIN Lock:
The following menu options can be used to change the
behavior of PIN Lock:
• “
PIN Brakes
” toggle whether triggering the PIN Lock will
lock all four brake when the vehicle is stopped. This is
disabled by default.
• “
PIN Horn
” toggle whether triggering the PIN Lock will
cause the horn to honk in a randomized pattern. This is
disabled by default.
• “
PIN Lights
” toggle whether triggering the PIN Lock will
start a Light Show. This is disabled by default.
• “
PIN Pedal
” toggle whether triggering the PIN Lock or
vehicle alarm, or an attempt to pair a key, will disable the
gas pedal. This is disabled by default.
Note:
This setting will remain in effect even if PIN Enable
has been turned off. The pedal will also be disabled if the
vehicle alarm is triggered or a key pairing is attempted.
Note:
While the pedal is disabled, several warning
chimes and lights will trigger as if there are vehicle
errors. If the pedal is reenabled while the vehicle is
running, the engine may stumble or stall.
• “
KillByFob
” toggle whether locking the vehicle from the
fob will disable the gas pedal. This is enabled by default.
Note:
The exterior lights will flash two additional times to
confirm the pedal has been disabled/enabled. Unlocking
using the same fob will reenable the pedal.
Note:
This setting will remain in effect even if the PIN
function has been turned off.
Note:
If the vehicle is unlocked with key or proximity
entry using using a different keyfob, the PIN will need to
be entered even if the PIN Lock has been turned off with
the “Enable/Disable PIN” option.
• “
Carjack
” toggle Carjack Mode, which triggers when the
key exits a running vehicle. The is disabled by default
and requires that a PIN is set and that PIN is enabled.
• “
PIN Clear Time
” set whether it should take 10 or 60
minutes to clear a forgotten PIN using the process
described above. This is set to 10 minutes by default.
