YUGE CLM920 AC5 Hardware Manual Download Page 3

Page: 3 / 39

CLM920_AC5 Mini PCIE LTE Module Hardware Manual

Shanghai Yuge Information Technology co., LTD

- 3 -

Contents

Chapter 1. Introduction...........................................................................................................- 7 -
Chapter 2. Product Overview................................................................................................. - 9 -

2.1 Product introduction................................................................................................. - 9 -
2.2 Module characteristics..............................................................................................- 9 -
2.3 Module function..................................................................................................... - 11 -

Chapter 3. Interface Application Description.......................................................................- 13 -

3.1 Overview................................................................................................................ - 13 -
3.2 Module interface.....................................................................................................- 13 -

3.2.1 52-pin gold finger........................................................................................- 13 -
3.2.2 Interface definition...................................................................................... - 14 -

3.3 Power interface.......................................................................................................- 17 -
3.4 Power on / off reset mode.......................................................................................- 19 -

3.4.1 Boot sequence..............................................................................................- 20 -
3.4.2 Power off..................................................................................................... - 20 -
3.4.3 Reset control................................................................................................- 20 -

3.5 USB interface......................................................................................................... - 21 -
3.6 UART interface...................................................................................................... - 23 -
3.7 USIM interface....................................................................................................... - 24 -

3.7.1 USIM card reference circuit........................................................................ - 24 -
3.7.2 USIM_DET Hot Swap Reference Design...................................................- 25 -

3.8 General GPIO interface.......................................................................................... - 26 -
3.9 Network indication interface.................................................................................. - 27 -
3.10 RF antenna interface.............................................................................................- 27 -

3.10.1 RF connector location................................................................................- 28 -
3.10.2 RF connector size...................................................................................... - 28 -
3.10.3 PCM digital voice interface.......................................................................- 30 -

Chapter 4. Overall technical indicators................................................................................ - 32 -

4.1 Overview of this chapter........................................................................................ - 32 -
4.2 working frequency..................................................................................................- 32 -
4.3 Conducted RF measurement...................................................................................- 32 -

4.3.1 Test environment......................................................................................... - 32 -
4.3.2 Standard test................................................................................................ - 33 -

Summary of Contents for CLM920 AC5








































Search results

Summary of Contents for CLM920 AC5

Reviews:

Related manuals for CLM920 AC5

Brands by name

Popular brands

YUGE CLM920 AC5, Hardware Manual

Search results

Summary of Contents for CLM920 AC5

Reviews:

Related manuals for CLM920 AC5

Brands by name

Popular brands