background image

 

51 

1. Principles of selecting anti-freeze solution 

1)  Select  anti-freeze  solution  of  different  freezing  points  according  to  the  ambient 

temperature. 

Its  freezing  point  should  be  approximately  10

  lower  than  the  lowest  temperature 

recorded in the region’s history. 

2)  Select  anti-freeze  solution  according  to  the  number  of  vehicles  and 

vehicle-concentration. 

For those units or departments with quite a number of vehicles that are more often used 

in one region, small-package anti-freeze mother liquid can be selected, which is stable in 

performance and convenient for transportation and storage. It can also be modulated in 

many  flexible  ways  according  to  the  use  condition,  achieving  conservation  and 

practicality.  If  there  is  only  limited  number  of  vehicles  and  they  are  used  in  different 

regions, you can choose the direct-use type anti-freeze solution. 

1)

 

Use high quality anti-freeze solution, never use inferior quality ones. 

High quality anti-freeze solution is usually certified as passing the inspection by the State 

designated inspection stations. From the exterior appearance, it should be crystal clear, 

not turbid and have  no foreign material or irritating  smell. The  external  packing should 

bear  detailed  information  on  the  manufacturer  name,  product  instruction  and  explicit 

indications.  Inferior  quality  anti-freeze  solution  will  not  be  able  to  be  anti-freeze  and 

anti-boiling; and quite on the contrary, it will accelerate corrosion to the cooling system. 

2)

 

Use anti-freeze solution that matches the rubber sealing component/pipe. 

Anti-freeze  solution  should  have  no  side  effect  on  the  rubber  sealing  component/part, 

such as swelling or encroachment. 

 

 

Summary of Contents for YC4D60-D21






















































Reviews: