background image

 

Foreword 

YC4D60-D21

YC4D85Z-D20  series  diesel  engines  are  developed  by  Yuchai  in  the 

purpose of satisfying the diesel generator set market requirement. This model bases on 

the  foundation  of  high-quality  product  YC4108Q

YC4108ZQ,  and  assimilate  the  diesel 

engine  technique    characteristics  of  generator  set,which  is  the  amalgamation  of  our 

company’s  abundant  experience  and  overseas  advanced  technology.YC4D85Z-D20 

engine  bases  on  the  model  of  YC4D60-D21  engine,  adopt  exhaust  gas  turbocharging 

technique ,which is good in motive force and fuel efficiency and meet the emission and 

low  noise  requirement.  The  series  has  good  performance  in  motive  force 

fuel 

efficiency and dependency. The model, compact, simple, easy maintenance. 

This  manual  introduces  the  main  technical  specifications

the  basic  assemblage 

requirements

the  engine  adjustment

the  operation  and  maintenance  and  the 

troubleshooting  of  the  YC4D60-D21

YC4D85Z-D20  engine.  Proper  operation  and 

maintenance  will  prolong  the  use  life  and  ensure  safety  in  operation.  Please  read  this 

Manual carefully before use, and pay special attention to CAUTIONS ON ENGINE USE. To 

ensure the engine use properly and maximize the client’s economic effectiveness, please 

make the engine maitenance work actually. 

This manual is only about the basic model of this series generator set ,which is the 

same  for  operation  and  maintenance  the  modified  models.As  requirements  for 

technology is developed so fast,modification will be carried out without information.   

              This manual is explained by YUCHAI Technology Centre and YUCHAI Technology 

Service Centre takes charge of the technology consults and advices. 

 

                                                                  Guangxi Yuchai Machinery Co. Ltd 

 

 

 

 

Summary of Contents for YC4D60-D21






















































Reviews: