background image

OPERATING & MAINTENANCE MANUAL                                                                                                                                MODEL :    ELB series 

 
 

  YOUYANG AIRPORT LIGHTING EQUIPMENT INC.                                                      PAGE 31/34 

5. STORAGE & SHIPPING 

5.1 STORAGE 

1) All light fixtures are packed in a separate box with label indicating its contents. 

2) Lighting fixtures shall be stored indoor under dry condition kept away from dust. 

 

5.2 STORAGE CONDITION 

1) Place                                            : Dry place without dust 
2) Temperature :                              : From -55˚C to 70˚C 
3) Humidity                                      : Below 90%   

 

5.3 SHIPPING 

1) 

The heavier package of the light fixtures shall be placed at the bottom and lighter 

box of package shall be placed on the upper position.   

2) Bigger outer box covering smaller boxes of package shall indicate contents of the 

boxes in a label. 

3) Racks, boxes and closed containers may be used for shipping. 

4)  Precautions  shall  be  taken  before  opening  the  shipping  container  to  protect  the 

contents of the package from dust or impurities. . 

5) Shipment shall be made in compliance with General Terms and Conditions for air 

and ocean freight.   

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for ELB Series



































Reviews: