Yosemite DF-EFP300U Instruction Manual Download Page 4

4 | 

P a g e

 

 

 

IMPORTANT SAFETY INSTRUCTIONS

_________________________________________ 

When using electric fireplaces, basic precautions should always be followed to reduce the risk of 
fire, electric shock and injury to persons, including the following: 

1.

 

Read all instructions before using this heater. 

2.

 

This fireplace is hot when in use. To avoid burns, do not let bare skin touch hot surfaces, such as 
surfaces  near  the  heater  outlet  or  light  bulbs.  Keep  combustible  materials  such  as  clothes, 
pillows, furniture, bedding, papers and curtains at least 3 feet from the front of this appliance.  

3.

 

CAUTION:

 Whenever the heater is left operating and unattended, extreme caution is necessary 

if children or invalids are nearby. 

4.

 

Do  not  install  the  fireplace  directly  on  carpet  or  a  similar  surface,  which  may  restrict  air 
circulation beneath the unit. 

5.

 

Always unplug fireplace when not in use. Disconnect the heater by turning controls to off then 
remove  plug  from  outlet  before  performing  any  cleaning,  maintenance  or  relocation  of  the 
fireplace. 

6.

 

Fireplace is designed for indoor and household use only. 

7.

 

This  fireplace  is  not  intended  for  use  in  wet  locations  such  as  bathrooms,  laundry  areas  and 
similar  indoor  locations.  Never  locate fireplace  where  it  may  fall into a  bathtub or  other  water 
container. 

8.

 

If the fireplace shows any signs of damage or if the heater has malfunctioned. Return fireplace to 
authorized service for examination, adjustment or repair. 

9.

 

Do not run cord under carpeting or route cord under furniture or appliance. Do not cover cord 
with  throw  rugs  and  runners.  Arrange  cord  away  from  traffic  areas  and  where  it  will  not  be 
tripped over.  

10.

 

Do  not  insert  or  allow  foreign  objects  to  enter  any  ventilation  or  exhaust  opening  as  this  may 
cause an electric shock, fire, or may damage the heater. 

11.

 

All electrical heaters have hot and arcing or sparking parts inside. Do not use it in areas where 
gasoline,  paint,  or  flammable  liquids  are  used  or  stored  or  where  the  unit  will  be  exposed  to 
flammable vapours. 

12.

 

Always use properly grounded, fused and polarized outlets. Always use ground fault protection 
where required by electrical code.  

13.

 

Extension cord may become overheat and may cause a risk of fire.  If you have to use an extension 
cord, the cord shall be 16AWG minimum size and rate not less than 125V/15A or 2500 watts. 

14.

 

This  appliance  is  not  intended  for  use  by  persons  (including  children)  with  reduced  physical, 
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given 
supervision  or  instruction  concerning  use  of  the  appliance  by  a  person  responsible  for  their 
safety. Children should be supervised to ensure that they do not play with the appliance. 

15.

 

CAUTION: 

In  order  to  avoid  a  hazard  due to  inadvertent  resetting  of the  thermal cutout,  this 

appliance  must  not  be  supplied  through  an  external  switching  device  such  as  a  timer,  or 
connected to a circuit that is regularly switched on and off by the utility. 

Summary of Contents for DF-EFP300U
















Reviews: