background image

10 | 

P a g e

 

 

 

 

ELECTRICAL WORKS INSTRUCTIONS

_________________________________________ 

This fireplace must be grounded 

 

1.

 

A standard electrical outlet must be close to the fireplace. If the electric outlet is required 

to be concealed, it can be located above or on the right hand side of the fire and behind 

the glass face. 

2.

 

DO  NOT  INSTALL  THE  FIREPLACE  WHERE  THE  HEATER  IS  DIRECTLY 

ABOVE AN OUTLET.

 The heater is located in the center of the fireplace base.  

3.

 

If the power supply cable becomes damaged in any manner it 

MUST 

be replaced.  

4.

 

Always  ensure  that  all  electrical  work  complies  with  the  relevant  Building  Codes.  All 

electrical work should be carried out by a qualified electrician.  

5.

 

Please observe these instructions as failure to do so may result in electric shock or other 

injury.  

 

 

GROUNDING INSTRUCTIONS

___________________________________________________ 

This  fireplace  is  for  use  on  120  volts.    The  cord  has  a  plug  as  shown  in  (A)  at 

Figure  5

.    An 

adapter as shown in (C) is available for 

connecting three-blade grounding type 

plugs  to  two-slot  receptacles.    The 

green  grounding  lug  extending  from 

the  adapter  must  be  connected  to  a 

permanent  ground  such  as  a  properly 

grounded  outlet  box.    The  adapter 

should  not  be  used  if  a  three-slot 

grounded receptacle is available.  

 

      Fig. 5 

Summary of Contents for DF-EFP300U
















Reviews: