manualshive.com logo in svg

York YDCC018-115, Installation Manual, Page: 2 / 12

Share
Download
York YDCC018-115 Installation Manual Download Page 2

  

YORK VRF Air-Conditioner IOM

 

Contents 

1 SAFETY CONSIDERATIONS ......................................................................................................

2 BEFORE INSTALLATION...........................................................................................................................................

 

 2

 

3 SELECTING INSTALLATION SITE ...............................................................................................................................

 

 2

 

4 BEFORE INSTALLATION...........................................................................................................................................

 

 3

 

5 INDOOR UNIT INSTALLTION....................................................................................................................................

 

 4

 

6 REFRIGERANT PIPING WORK................................................................................................................................

 

.. 4

 

7 DRAIN PIPING WORK .............................................................................................................................................

 

 6

 

8 INSTALLING THE DUCT ...........................................................................................................................................

 

 7

 

9 SET THE ESP ...........................................................................................................................................................

 

 7

 

10 ELECTRIC WIRING WORK......................................................................................................................................

 

 7

 

 ............................

͘

... 

ϭ

Summary of Contents for YDCC018-115













Reviews:

No comments