background image

Read this manual carefully before using this air-conditioner. If you still have any 
difficulties or problems, consult your dealer for help. 
The air-conditioner is designed to provide you with comfortable room conditions. Use 
this unit only for its intended purpose as described in this instruction manual.

WARNING

We recommend that this air-conditioner is installed properly by qualified installation technicians in accordance 
with the installation instructions provided with the unit. 
Before installation, check if the voltage of the power supply at installation site is the same as the voltage 
shown on the nameplate. 

You must not carry on any transformation to this product, otherwise, it may possibly 
cause such consequences as water leakage, the breakdown, the short-circuit,  
electric shock, fire, etc.
The work such as piping welding, etc. should be carried out far away from the 
flammable explosive material vessels, including the air-conditioner refrigerant, to 
guarantee the security of the site.
To protect the air-conditioner from heavy corrosion, avoid installing the outdoor unit 
where salty seawater can splash directly onto it or in sulphurous air near a spa. Do 
not install the air-conditioner where excessively high heat-generating objects are 
placed. 

CAUTION Statements

1

DANGER

If the supply cord is damaged, it must be replaced by the factory or its service department 
in case of danger.
The place where this product is installed must have the reliable electrical earth facility and 
protections. Please do not connect the grounding of this product to various kinds of air-
feeding ducts, drain piping,lightning protection facility as well as other piping lines to avoid 
receiving an electric shock and damages caused by other factors. 
Wiring must be done by a qualified electrician. All the wiring must comply with the local 
electrical codes. 
Consider the capacity of the electric current of your electrical meter and socket before 
installation. 
The power wire where this product is installed is supposed to have the independent 
leakage protective device and the electric current over-load protection device which are 
provided for this product.
This appliance  is not intended for use by persons who lack of experience and knowledge, 
unless they have been given supervision or instruction concerning use of the appliance by 
a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance. Means 
for disconnection, which can provide full disconnection in all poles, must be incorporated 
in the fixed wiring in accordance with the wiring rules .

Never use gasoline or other inflammable gas near the air-conditioner, which is very 
dangerous. 
When the air conditioner operation is abnormal, such as burnt smell,deformation, fire, 
smoke,etc., it is forbidden to continue using the air conditioner, the main power switch 
of the air conditioner must be cut off immediately and the agent must be contacted.

Do not turn the air-conditioner on and off from the power main switch. Use the 
ON/OFF operation button.
Do not stick anything into the air inlet and air outlet of both the indoor and outdoor 
units. This is dangerous because the fan is rotating at a high speed. 

WARNING

CAUTION

Summary of Contents for YAJN12BZNWETH1




















Reviews: