background image

5300477-UIM-A-0317

Johnson Controls Unitary Products

3

LOCATION

Use the following guidelines to select a suitable location for these units:

1.

Unit is designed for 

outdoor installation

 only.

2.

Outdoor coils must have an unlimited supply of air. Where a choice
of location is possible, position the unit on either north or east side
of building.

3.

Suitable for mounting on roof curb.

4.

For ground level installation, a level pad or slab should be used.
The thickness and size of the pad or slab used should meet local
codes and unit weight. Do not tie the slab to the building foundation.

5.

Roof structures must be able to support the weight of the unit and
its options/accessories. Unit must be installed on a solid, level roof
curb or appropriate angle iron frame.

6.

Maintain level tolerance to 1/8” across the entire width and length of
unit.

CLEARANCES

All units require certain clearances for proper operation and service.
Refer to Table 4 for the clearances required for construction, servicing
and proper unit operation.

RIGGING AND HANDLING

Exercise care when moving the unit. Do not remove any packaging until
the unit is near the place of installation. Rig the unit by attaching chain
or cable slings to the lifting holes provided in the base rails. Spreader
bars, whose length exceeds the largest dimension across the unit,

MUST

 be used across the top of the unit.

Units may be moved or lifted with a forklift. Slotted openings in the base
rails are provided for this purpose.

 FIGURE 1:  

Component Location

OUTDOOR FAN MOTOR

OUTDOOR FAN

COIL GUARD PANEL

OUTDOOR COIL

(Behind Panel)

CONTACTOR

TRANSFORMER

CAPACITOR

BLOWER MOTOR

TXV

INDOOR COIL

INDOOR BLOWER

COMPRESSOR

REMOVABLE
BASE RAILS

A0411-001

OPTIONAL
ELECTRIC HEAT KIT

ECM BLOWER MOTOR
CONTROL BOARD

 WARNING

Do not attach supply and return duct work to the bottom of the unit
base pan as the drain pan could be compromised.

 WARNING

Do not permit overhanging structures or shrubs to obstruct outdoor
air discharge outlet. 

!

!

 CAUTION

If a unit is to be installed on a roof curb other than a Unitary Products
roof curb, gasket or sealant must be applied to all surfaces that come
in contact with the unit underside.

 CAUTION

All panels must be secured in place when the unit is lifted.
The outdoor coils should be protected from rigging cable damage
with plywood or other suitable material.

 CAUTION

Before lifting, make sure the unit weight is distributed equally on the
rigging cables so it will lift evenly.

!

!

!

Summary of Contents for PCE6 SERIES





















Reviews: