background image

BLOWER PERFORMANCE - DOWNFLOW - CFM (Includes Filter)

MODEL

SPEED

TAP

EXTERNAL STATIC PRESSURE, INCHES W.C.

0.10

0.20

0.30

0.40

0.50

0.60

0.70

0.80

0.90

1.00

P2DPD10

*

04801

HIGH

1356

1315

1222

1154

1090

988

888

771

630

462

MED

1144

1080

1023

958

919

830

740

635

510

425

LOW

967

942

908

864

811

747

672

574

476

344

P2DPD12

*

06401

HIGH

1557

1502

1410

1344

1240

1142

1025

882

740

567

MED

1289

1238

1175

1098

1030

938

855

712

582

455

LOW

1136

1081

1039

965

906

831

739

617

515

413

P2DPD12

*

08001

HIGH

1599

1535

1465

1375

1277

1182

1089

948

723

554

MED

1390

1327

1266

1195

1109

1027

919

813

597

458

LOW

1175

1136

1093

1027

967

900

816

764

497

382

P2DPD16

*

08001

HIGH

2043

2000

1893

1823

1726

1627

1503

1382

1249

1134

MED

1706

1655

1593

1533

1450

1366

1265

1163

1062

950

LOW

1452

1406

1373

1317

1245

1174

1112

1025

935

817

P2DPD16

*

09201

HIGH

2053

1977

1899

1817

1725

1623

1519

1401

1265

1120

MED

1711

1667

1606

1530

1458

1383

1284

1184

1066

951

LOW

1460

1434

1407

1363

1310

1232

1137

1064

964

854

P2DPD20

*

10401

HIGH

2330

2248

2177

2103

2024

1910

1789

1698

1555

1419

MED

1867

1858

1814

1740

1675

1593

1524

1443

1330

1204

LOW

1613

1531

1516

1490

1495

1411

1337

1250

1225

1010

              Operation at these heating conditions exceed the listed temperature rise range. A higher blower
        

speed 

must 

be 

selected.

*  Model designator may be "N" for standard units, or "L" for factory built  low NOx units.
  Airlfow is expressed in standard cubic feet per minute.
  Motor voltage at 115V

650.69-N3

22

Unitary Products Group

Summary of Contents for P2DP Series

























Reviews: