background image

5715184-BIM-A-0519

Johnson Controls Ducted Systems

9

SECTION III: FILTERS

FILTER INSTALLATION

All applications require the use of a field installed filter. All filters and
mounting provision must be field supplied.

Filters must be installed external to the furnace cabinet. 

DO  NOT

attempt to install filters inside the furnace.

1. Air velocity through throwaway type filters must not exceed 300 ft per minute 

(91.4 m/min). All velocities over this require the use of high velocity filters.

2. Do not exceed 1800 CFM using a single side return and a 16 x 25 filter. For 

CFM greater than 1800, you can use two side returns or one side and the 
bottom or one side return with a transition to allow use of a 20 x 25 filter.

SIDE RETURN - UPFLOW ONLY

Locate the L shaped corner locators. These indicate the size of the cut-
out to be made in the furnace side panel. Refer to Figure 10.

Install the side filter rack following the instructions provided with that
accessory. If a filter(s) is provided at another location in the return air
system, the ductwork may be directly attached to the furnace side
panel.

 FIGURE 9:  

Dimensions (Upflow Configuration Shown)

)5217

$

/()76,'(

&RPEXVWLRQ$LU,QOHW

&RQGHQVDWH'UDLQ
'RZQIORZ

7KHUPRVWDW
:LULQJ

´

*DV3LSH
(QWU\

(OHFWULFDO
(QWU\

&RQGHQVDWH
'UDLQ

7KHUPRVWDW
:LULQJ

5,*+76,'(

&RQGHQVDWH'UDLQ
'RZQIORZ

´

´

´

´

&RPEXVWLRQ$LU,QOHW

*DV3LSH
(QWU\

(OHFWULFDO
(QWU\

&RQGHQVDWH
'UDLQ

2SWLRQDO5HWXUQ$LU
&XWRXW(LWKHUVLGH

´

)RU&ODGGHGGRRUDGGDSSR[LPDWHO\DQDGGLWLRQDO´

&

6833/<(1'

´

´

´

%

´

´

´

&RPEXVWLRQ
$LU,QOHW

5(7851(1'

%

´

´9HQW
&RQQHFWLRQ
2XWOHW

´9HQW
&RQQHFWLRQ
2XWOHW

´9HQW
&RQQHFWLRQ
2XWOHW

$

Table 2: 

Cabinet and Duct Dimensions - MM9E

BTUH (kW)

Input

Nominal

CFM (m

3

/min)

Cabinet

Size

Cabinet Dimensions (Illustrated in Figure 9)

Approximate

Operating Weights

A (in.)

A (cm)

B (in.)

B (cm)

C (in.)

C (cm)

lbs

60 (17.6)

1200 (34.0)

B

17 1/2

44.4

16 3/8

41.6

13 1/4

33.7

122

80 (23.4)

1200 (34.0)

B

17 1/2

44.4

16 3/8

41.6

14 3/4

37.5

126

80 (23.4)

1600 (45.3)

C

21

53.3

19 7/8

50.5

16 1/2

41.9

136

80 (23.4)

2000 (56.6)

C

21

53.3

19 7/8

50.5

16 1/2

41.9

139

100 (29.3)

1600 (45.3)

C

21

53.3

19 7/8

50.5

18 1/4

46.4

142

NOTICE

Single side return above 1800 CFM is approved as long as the filter
velocity does not exceed filter manufacturer’s recommendation and
a transition is used to allow use on a 20x25 filter.

Table 3: 

Recommended Filter Sizes (High Velocity 600 FPM)

CFM

(m³/min)

Cabinet

Size

Side

(in.)

Bottom

(in.)

1200 (34.0)

B

16 x 25

16 x 25

1600 (45.3)

C

16 x 25

20 x 25

2000 (56.6)

C

(2) 16 x 25

20 x 25

 FIGURE 10:  

Side Return Cutout Markings

IMPORTANT: 

Some accessories such as electronic air cleaners

and pleated media may require a larger side opening. Follow the
instructions supplied with that accessory for side opening require-
ments.  Do  not cut the opening larger than the dimensions for the
Optional Return Air Cutout shown in Figure 9.

)52172)
)851$&(

&251(5
0$5.,1*6

6,'(2)
)851$&(

$

Summary of Contents for MM9E Series





































Reviews: