York MILLENNIUM YCAS0373, Wiring Diagram

Page: 4 / 28

YORK INTERNATIONAL
4
ELECTRICAL DATA
NOTES
1. MRC is Maximum Running Current, the maximum continuous current at any operating point in the rating range. Also referred to as MCA,
or Minimum Current Ampacity to be furnished by the installer.
2. The recommended disconnect switch is based on a minimum of 115% of the summation rated load amps of all the loads included in the
circuit, per N.E.C. 440 - 12A1.
3. Minimum fuse size is based on 150% of the largest motor RLA plus 100% of the remaining RLAs (U.L. Standard 1995, Section 36.1).
Minimum fuse rating = (1.5 x largest compressor RLA) + other compressor RLAs + (# fans x each fan motor FLA).
4. Maximum dual element fuse size is based on 225% maximum plus 100% of the rated load amps for all other loads included in the circuit,
per N.E.C. 440-22. Maximum fuse rating = (2.25 x largest compressor RLA) + other compressor RLAs + (# fans x each fan motor FLA).
5. Minimum circuit breaker is 150% maximum plus 100% of rated load amps included in the circuit, per circuit per U.L. 1995 Fig. 36.2.
Minimum circuit breaker rating = (1.5 x largest compressor RLA) + other compressor RLAs + (# fans x each fan motor FLA).
6. Maximum circuit breaker is based on 225% maximum plus 100% of the rated load amps for all loads included in the circuit, per circuit,
per U.L. 1995 Fig. 36.2. Maximum circuit breaker rating = (2.25 x largest compressor RLA) + other compressor RLAs + ( # fans x each
fan motor FLA).
7. The Incoming Wire Range is the minimum and maximum wire size that can be accommodated by unit wiring lugs. The (1), (2), or (3)
indicate the number of termination points or lugs which are available per phase. Actual wire size and number of wires per phase must
be determined based on ampacity and job requirements using N.E.C. wire sizing information. The above recommendations are based
on the National Electric Code and using copper connectors only. Field wiring must also comply with local codes.
8. A ground lug is provided for each compressor system to accommodate field grounding conductor per N.E.C. Article 250-54. A control
circuit grounding lug is also supplied. Incoming ground wire range is #6 - 350 MCM.
9. The field supplied disconnect is a “Disconnecting Means” as defined in N.E.C. 100.B, and is intended for isolating the unit from the
available power supply to perform maintenance and troubleshooting. This disconnect is not intended to be a Load Break Device.
10. Two-Compressor machines with single-point power connection, and equipped with Star-Delta Compressor motor starters, must also
include Factory-provided circuit breakers in each motor control center. 3 & 4 Compressor machine equipped with Star-Delta compressor
motor starter, must also include factory-provided circuit breakers in each motor control center.
11. Consult factory for Electrical Data on units equipped with “High Static Fan” Option. High Static Fans are 3.5 kW each.
12. FLA for “Low Noise Fan” motors is 4.1 A.
MULTIPLE POINT 380V / 50HZ / 3Ø POWER SUPPLY CONNECTION
Each of Two Field Provided Power Supply Circuits individually protected with Branch Circuit Protection.
Field Connections to Factory provided Terminal Block (Std), Disconnects (Opt), or Breakers(Opt) in each of the two Motor Control Centers.
* “Optional” Circuit Breakers are REQUIRED for units with CE mark.
CHILLER
ELECTRICAL SYSTEM #1 FIELD SUPPLIED WIRING
MODEL
FIELD PROVIDED POWER SUPPLY FACTORY PROVIDED (LUGS) WIRE RANGE 7 COMPRESSOR DATA FAN
YCAS
MRC MIN NF OVER-CURRENT PROTECTION STANDARD* OPTIONAL* NF OPTIONAL DATA
11, 12
(MCA 1) DISC SW 2 MIN. 3, 5 MAX. 4, 6 TERMINAL BLOCK DISC. SWITCH CIRCUIT BREAKER
RLA Y-LRA X-LRA
QTY FLA (EA)
0373SB 148 150 200 250 # 2 - 4/0 # 6 AWG - 350 # 6 AWG - 350 108 241 761 3 4.4
0403SB 160 200 200 250 # 2 - 300 # 6 AWG - 350 # 6 AWG - 350 118 241 761 3 4.4
0453SB 188 200 225 300 # 2 - 300 # 6 AWG - 350 # 6 AWG - 350 140 309 979 3 4.4
0503SB 215 250 300 350 # 1 - 500 # 6 AWG - 350 (2) 3/0-250 161 309 979 3 4.4
0543SB 193 200 250 300 # 2 - 300 # 6 AWG - 350 # 6 AWG - 350 141 309 979 4 4.4
0573SB 227 250 300 350 # 1 - 500 # 6 AWG - 350 (2) 3/0-250 168 309 979 4 4.4
0623SB 247 250 300 400 # 1 - 500 # 6 AWG - 350 (2) 3/0-250 183 309 979 4 4.4
0653SB 232 250 300 350 # 1 - 500 # 6 AWG - 350 (2) 3/0-250 168 309 979 5 4.4