8
ENGLISH
PARTS INSTALLATION
■
Cautions on remote controller installation
• Before installation, operate the remote controller to
determine its location in a reception range.
• Keep the remote controller at least 1 m apart from the
nearest TV set or stereo equipment.
• Do not install the remote controller in a place exposed to
direct sunlight or close to a heating source, such as a stove.
• Note that the positive and negative poles are right
positions when loading batteries.
The air-conditioner can be connected only to a supply
with system impedance no more than 0.26 ohm. In case
necessary please consult your supply authority for system
impedance information.
NOTE: At least two of A, B, C aspect are free from blocking.
3
2
1
4
C
A
B
5
6
15cm or more
12cm or more
12cm or more
Air filter
Remote controller
Mounting screw B
ST2.9x10-C-H
Remote controller
holder
Loop the
connective
cable.
10cm or more
Air blowing
direction
60cm or more
100cm
or m
ore
10cm or more
60
cm
or m
ore
INDOOR UNIT
INSTALLATION PROCEDURE
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
■
Fixing
• Place the installation guide pattern on the designated
installation place and mark the hole position.
• Drill a hole and mount installation plate.
• After determining the pipe
hole position drill the hole at
a slight downward slant
towards the outdoor side.
ø 65 mm
Outdoor
Indoor
Note: When installing
the refrigerant pipes from
others side. A hole must
be place to allow fall
towards the outdoor unit.
20
30
70
750
54
05
2
MODEL 07-09, 12 [220-240V, 50/60Hz]
Indoor unit outline
15 cm or more to
ceiling
Installation plate
12 cm or more
to wall
12 cm or more
to wall
Left
refrigerant
pipe hole
ø65 mm
Right refrige-
rant pipe hole
ø65 mm
• Make 6 mm 4-6 holes, in the wall at the four corners of mouting
plate (bracket) then insert appropriate mounting devices.
• Install the mounting plate using 4-6 pieces of mounting screw
securely at four corners and tighten the screw completely.
Do not over tighten the screws and deform the back plate.
Part No.
Name of part
Q’ty
1
Installation plate
1
2
Mounting screw ST3.9x25-C-H
8
3
Clip anchor
8
4
Refrigerant
Liquid side
pipe
Gas side
5
Remote controller
1
6
Remote controller holder
1
7
Seal
1
8
Drain elbow
1
280
815
50
50
MODEL 12 [115V, 60Hz (UL)]
Left
refrigerant
pipe hole
ø65 mm
Right refrige-
rant pipe hole
ø65 mm
12 cm or more
to wall
12 cm or more
to wall
Indoor unit outline
15 cm or more to
ceiling
Installation plate
Parts you
must
purchase
J174_lastRev4.pmd
3/14/05, 3:27 PM
8
