background image

279550-YIM-A-0207

Unitary Products Group

27

Adjustment of Temperature Rise

After about 20 minutes of high heat operation, determine the 
furnace temperature rise. Take readings of both the return air 
and the heated air in the ducts about six feet from the furnace 
where they will not be affected by radiant heat.

The temperature rise (or temperature difference between the 
return air and the heated air from the furnace) must lie within 
the range shown on the rating plate and the data in Tables 9 
and 11.

After the temperature rise has been determined, the CFM can 
be calculated as follows:

Direct Drive Blower

All units have direct drive, constant CFM blower motors.

Checking Gas Heat Input

Natural Gas

1.

Turn off all other gas appliances connected to the gas meter.

2.

With the furnace turned on, measure the time needed for 
one revolution of the hand on the smallest dial on the 
meter. A typical gas meter usually has a 1/2 or a 1 cubic 
foot test dial.

3.

Using the number of seconds for each revolution and the 
size of the test dial increment, find the cubic feet of gas 
consumed per hour from Table 19.

If the actual input is not within 5% of the furnace rating with 
allowance being made for the permissible range of the regulator 
setting, replace the orifice spuds with spuds of the proper size.

NOTE: 

To find the BTU input, multiply the number of cubic feet 
of gas consumed per hour by the BTU content of the gas 
in your particular locality. (Contact your gas company for 
this information since it varies widely from city to city.)

%78+2XWSXW

[&)0

25

&)0   

%78+2XWSXW

'HJUHHV)7HPS5LVH   

['HJUHHV)7HPS5LVH

Table 19: Gas Rate Cubic Feet Per Hour

1

1.

EXAMPLE

: By actual measurement, it takes 38 seconds for the 

hand on the 1-cubic foot dial to make a revolution with just a 
100,000 BTUH furnace running. Using this information, locate 
38 seconds in the first column of Table 19. Read across to the 
column headed “1 Cubic Foot,” where you will see that 95 cubic 
feet of gas per hour are consumed by the furnace at that rate. 
Multiply 95 x 1050 (the BTU rating of the gas obtained from the 
local gas company). The result is 99,750 BTUH, which is close 
to the 100,000 BTUH rating of the furnace.

Seconds for

One Rev.

Size of Test Dial

1/2 cu. ft.

1 cu. ft.

10

180

360

12

150

300

14

129

257

16

113

225

18

100

200

20

90

180

22

82

164

24

75

150

26

69

138

28

64

129

30

60

120

32

56

113

34

53

106

36

50

100

38

47

95

40

45

90

42

43

86

44

41

82

46

39

78

48

37

75

50

36

72

52

35

69

54

34

67

56

32

64

58

31

62

60

30

60

Summary of Contents for AFFINITY DNX024





































Reviews: