YOKOGAWA Dpharp vigilantplant EJA110A, User Manual

Page: 19 / 40

<3. Installation>
17
IM 01C22A01-01E
IMPORTANT
The transmitter should be installed below the high
pressure (HP) process connection to ensure a
positive head pressure of
fi
ll
fl
uid. The recommended
height between the HP process connection and the
transmitter is show in the following table. Pay special
attention to vacuum applications.
Model Height (h)
EJA118 600 mm
EJA438W Wetted parts material code S,
T, U, EJA438N
700 mm
EJA438W Wetted parts material code H 1,300 mm
Wetted parts material code
If it can not be installed below the HP process
connection with the recommended height above,
please use the equation below:
h= ×7.5×10
–3
[mm]
(P–P0)×dHg
ds
h: Vertical height between the HP process connection
and the transmitter (mm)
h
≤
0: Install the transmitter at least h (mm) below
the HP process connection
h>0: Install the transmitter at most h (mm) above
the HP process connection
P: Pressure in the tank (Pa abs)
P0: Minimum working pressure limit of the transmitter
(ambient temperature range: -10 to 50°C)
EJA118
Wetted parts material
code
S T H U
P0: Minimum working
pressure limit
3178 3596 6074 4711
EJA438
Wetted parts material
code
S T, U H
P0: Minimum working
pressure limit
5254 6980 13019
ds: Speci
fi
c gravity of
fi
ll
fl
uid (at 25°C)
Fill
fl
uid code A B C, E D
ds: Speci
fi
c gravity
1.07 0.94 1.09
1.90 to
1.92
dHg: Speci
fi
c gravity of the Mercury 13.6 (at 25°C)
Wetted parts material code
Fill fluid code
F0308.ai
P
h
Low
pressure side
0
High
pressure side
(+)
(–)
Figure 3.8 Example of Installation to Tank
(Caution on Installation)
3.4 Affi xing the Tefl on Film
IMPORTANT
The FEP Teflon option includes a teflon film and
fluorinated oil. Before mounting the transmitter to the
process
fl
ange, af
fi
x the te
fl
on
fi
lm as follows:
1) Position the diaphragm so that the diaphragm is in
an upward position.
2) Pour the
fl
uorinated oil on the diaphragm and
gasket area covering it completely and evenly. Be
careful not to scratch the diaphragm or change the
its shape.
3) Af
fi
x the te
fl
on
fi
lm over the diaphragm and gasket
area.
4) Next, carefully inspect the cover and try to identify
any entrapped air between the diaphragm and
the te
fl
on
fi
lm. The air must be removed to ensure
accuracy. If air pockets are present, use your
fi
ngers to remove the air by starting at the center of
the diaphragm and work your way out.
5) Place the gasket with the te
fl
on
fi
lm and af
fi
x to the
process
fl
ange.
F0309.ai
EJA210A F9347YD
EJA118W
EJA438W
F9347YA
2B
(50A)
F9347XA 3B(80A)
Teflon film
PART No.
Diaphragm
Fluorinated oil
[PART No. : F9145YN]
Gasket area
Figure 3.9 Affi xing the Tefl on Film
Installation
3