background image

26

11.  Maintenance and After-Sales Service

Please direct question about this product to the contact listed on the  
“Inquiries” or to your nearest Yokogawa dealer.
 

Recommended calibration period: 1 year

12.  Sales in Each Country or Region

12.1  Disposing the Product

Waste Electrical and Electronic Equipment (WEE),Directive

(This directive is valid only in the EU.)
This product complies with the WEEE directive marking requirement.
This marking indicates that you must not discard this electrical/ 
electronic product in domestic household waste.

Product Category

With reference to the equipment types in the WEEE directive,  
this product is classified as a “Monitoring and Control instrumentation”  
product.
When disposing products in the EU, contact your local  

Yokogawa Europe B.V. office.

 

Do not dispose in domestic household waste.

  

12.2  How to Replace and Dispose the Batteries

EU Battery Directive

(This directive is valid only in the EU.)

Batteries are included in this product.

When you remove batteries from this product and dispose them,  
discard them in accordance with domestic law concerning disposal.
Take a right action on waste batteries, because the collection system  
in the EU on waste batteries are regulated.

Battery type: Alkaline dry cell

  

Notice:

This marking indicates they shall be sorted out and collected as  
ordained in the EU battery directive.

How to remove batteries safely:

For further details, see “9.2 Battery Replacement”.

12.3  Authorized Representative in the EEA

Yokogawa Europe B.V. is the authorized representative of 

 

Yokogawa Meters & Instruments Corporation for  
this product in the EEA. (EEA: European Economic Area)

To contact Yokogawa Europe B.V., see the separate 

 

list of worldwide contacts, PIM 113-01Z2.

Summary of Contents for CW10































Reviews: