manualshive.com logo in svg

YIC Technologies EMScanner, User Manual

Share
Download
YIC Technologies EMScanner User Manual Download Page 41

 

 

www.yictechnologies.com 

 
 
 

It is important to activate all the probes under the DUT to have a complete view of the 
emissions from the DUT. 
 

Amplitude Adjustment Tab 

You can use an LNA or attenuator with EMScanner to increase or decrease the power level 
of the signals coming from the scanner and going to the spectrum analyzer. To activate click 
on Amplification Setting or Attenuator Setting and then select the value from the drop down 
menu or type the value. The displayed value of the signal will be corrected for the value of 
the gain or attenuation. 

Internal Analyzer Pre-Amp: 

This feature provides extra sensitivity. It is ON by default. Turn 

this feature OFF if your spectrum analyzer is not equipped with a Pre-Amp. 

Analyzer Tracking Generation: 

This feature will remotely turn on the tracking generator of the 

spectrum analyzer. When you run Spatial Scan, the tracking generator will output at the 
centre frequency selected for the Spatial Scan. The Tracking Generation Feature is currently 
available for the Keysight FieldFox N9912A. New drivers must be developed on demand for 
any other spectrum analyzer; contact Y.I.C Technologies (

[email protected]

) 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Description Tab 

You can name the node and add a description. Click OK.

 

 
 
 
 
 
 
 

 

Summary of Contents for EMScanner







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands