background image

 

17 

 

FIELD OPERATION 

 

PARKING THE ROTARY HOES 
 

3400 HOES 

 

Lower the parking stand.  Lower rotary hoe and loosen center link if necessary.  Release 
the latch levers and quick coupler, or raise center link latch handle and remove hitch pins, 
then move tractor. 
 

3500 HOES 

 

Fold  wings  to  the  down  position  unless  rear  parking  stand  is  used.    Lower  the  parking 
stands.    Lower  the  rotary  hoe  and  loosen  center  link  if  necessary.    Release  the  latch 
levers  and  quick  coupler,  or  raise  center  link  latch  handle  and  remove  hitch  pins,  then 
drive tractor away. 
 

 
 

CAUTION:  NEVER UNHOOK FROM A FOLDED ROTARY HOE UNLESS REAR 

PARKING STANDS ARE USED. 

 
TRANSPORTING THE HOES 
 

3400 HOES 

 

To change from field to transport position, raise the hoe.  Make certain the SMV symbol is 
in place before transporting.  DO NOT exceed 15 mph during transport. 
 

3500 HOES 

 

To  change  from  field  to  transport  position,  raise  the  hoe,  and  then  fold.    Make  certain 
there  is  adequate  clearance  for  the  wings  to  fold  without  hitting  obstructions.    Check 
gauge  wheel  positions  for  adequate  tractor  and  cab  clearance.    Make  certain  the  SMV 
symbol is in place.  DO NOT exceed 15 mph during transport. 
 
 

 
 

 

   CAUTION:  STAND CLEAR OF FOLDING WING! 

 

 
 

 

CAUTION:  ALWAYS FOLLOW ALL STATE, FEDERAL, AND LOCAL LAWS     
 

     WHEN TRANSPORTING ROTARY HOE ON PUBLIC ROADS. 

 
 
 
 

 

Summary of Contents for 3400 Series









































Reviews: