Yeastar Technology TG400G User Manual Download Page 103

Page: 103 / 104

TG Series User Guide

103/104

Download System Logs

Procedure

Navigate to

Status > Reports > System Logs

Choose the desired system log file, click

Delete System Logs

Procedure

Navigate to

Status > Reports > System Logs

Choose the desired system log file, click

Capture Ethernet Packet

Yeastar TG gateway provides an integrated tool to help you capture Ethernet packet on Web user
interface. You can debug the system efficiently with this tool.

Procedure

Navigate to

Status > Reports > System Logs

Packet Capture Tool

Choose the target Ethernet Interface.

(Optional)

Enter the target IP address.

(Optional)

Enter the target port.

Click

Start

The system will start to capture the Ethernet packet.

Click

Stop

to stop capturing packet.

Click

Download

to download the captured packet to your local PC and use Wireshark to open

the packet file.

Summary of Contents for TG400G









































































































Search results

Summary of Contents for TG400G

Reviews:

Related manuals for TG400G

Brands by name

Popular brands

Yeastar Technology TG400G, User Manual

Search results

Summary of Contents for TG400G

Reviews:

Related manuals for TG400G

Brands by name

Popular brands