background image

 

 

S-Series  IP  PBX  Administrator  Guide 

 

87 

Table 9-7 External Host Configuration Parameters

 

Option 

Description 

External Host 

Alternatively  you  can  specify  an  external  host,  and  the 

system will perform DNS queries periodically.     

This setting is only required when your external IP address 

is  not  static.  It  is  recommended  that  a  static  public  IP 

address be used with this system. Please contact your ISP 

for more information. 

External Refresh Interval 

If an external host has been supplied, you may specify how 

often  the  system  will  perform  a  DNS  query  on  this  host. 

This value is specified in seconds. 

Local Network Identification 

Used  to  identify  the  local  network  using  a  network 

number/subnet  mask  pair  when  the  system  is  behind  a 

NAT  or  firewall.  Some  examples  are  as  follows: 
“192.168.0.0/255.255.0.0”, 

“10.0.0.0/255.0.0.0”, 

and 

“172.16.0.0/12”. 

NAT Mode 

Global  NAT  configuration  for  the  system.  The  options  are 

as follows:   

 

Yes:  use  NAT  and  ignore  the  address  information  in 
the  SIP/SDP  headers  and  reply  to  the  sender's  IP 

address/port. 

 

No: use NAT mode only according to RFC3581. 

 

Never: never attempt NAT mode or RFC3581 support. 

Route: use NAT but do not include rport in headers.

 

Codec 

A codec is a compression or decompression algorithm that used in the transmission of voice packets 

over  a  network  or  the  Internet.  S-Series  supports  G711  a-law,  u-law,  GSM,  H261,  H263,  H263P, 

H264, SPEEX, G722, G726, ADPCM, G719A, MPEG4 and iLBC. 

 

Note: 

If you would like to use G.729, please enter your license. The system have embedded the G729, you 

can test it directly without purchasing license. But for copyright protection, we suggest you to buy it 

after testing it successfully. After you buy the license from DIGIUM, you should enter G729 license at 

the "G729 License Key". 

 

Summary of Contents for S20


































































































































Reviews: