Yealink VC110 Administrator'S Manual Download Page 155 | Manualshive

Page: 155 / 268

background image

Configuring Endpoint Settings

143

This chapter provides information for making configuration changes for the endpoint,
such as language, time and date, backlight of the video conferencing phone,
vido&audio settings and camera settings:

Topics include:



General Settings





Adjusting MTU of Video Packets



Dual-Stream Protocol





Configuring Camera Settings



Far-end Camera Control



Camera Control Protocol



Output Resolution



Video Recording





When the endpoint is idle, the site name is displayed on the status bar of display device
and video conferencing phone. You can make an IP address call to the far site, the site
name will be displayed on the display device of the far site. Site name can consist of
letters, numbers or special characters. You can configure the site name of the endpoint
via the remote control or web user interface.

The site name parameter is described below:

Parameter

Description

Configuration Method

Site Name

Configures the site name of the
endpoint.

Valid values: String within 64
characters

Remote Control

Web User Interface

«
...
153
154
155
156
157
...
»

Summary of Contents for VC110













































































































































































































































































Reviews:

No comments

Related manuals for VC110

Brand: a/d/s/ Pages: 14

Brand: Barco Pages: 2

Brand: Data Aire Pages: 28

Brand: Xantech Pages: 102

Brand: Yealink Pages: 8

Brand: iTrak Pages: 6

Safeline DNSL-IO2

Brand: DINA Pages: 28

Brand: VIS-A-VIS Pages: 4

Brand: Symetrix Pages: 4

Brand: Nakamichi Pages: 11

RS2135I - Compact Audio System

Brand: RCA Pages: 13

Brand: RCA Pages: 19

Brand: RCA Pages: 21

E84DGFCp Series

Brand: Lenze Pages: 100

Brand: Vicon Pages: 17

Brand: Boss Audio Systems Pages: 6

Brand: Sony Pages: 48

Brand: Sony Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands