manualshive.com logo in svg

Yealink VC110, Administrator'S Manual

The Yealink VC110 is an advanced video conferencing system that offers seamless communication and collaboration. To get the most out of this powerful device, you can easily download the user manual for free from our website, ensuring a smooth user experience and optimal utilization of its features.

Share
Download
background image

Administrator‘s Guide for Yealink VC110 Video Conferencing Endpoint 

176 

5.

 

Select the desired values from the pull-down lists of Far Move to Camera Presets. 

 

6.

 

Click Confirm to accept the change. 

To configure far-end camera control feature via the remote control: 

1.

 

Select Menu->Video & Audio->Far-end Camera Control. 

2.

 

Make the desired changes. 

3.

 

Press the Save soft key to accept the change. 

VC110 video conferencing endpoint supports camera control protocols: FECC (Far End 
Camera Control). You can enable the FECC protocol for SIP call or H.323 call.   

If far site wants to control the local camera, both the far site and near site should enable 
the camera control protocol simultaneously. If the FECC protocol is not enabled on either 
site, far-end camera control cannot be performed. For example, a SIP call is established 
between two sites, the two sites must enable FECC (SIP) protocol simultaneously to 
perform far-end camera control. If FECC (SIP) protocol and FECC (H.323) protocol are 
both enabled, the endpoint will select the appropriate camera control protocol 
according to the protocol (SIP or H.323) the call uses.   

Camera control protocol parameters are described below: 

Parameter 

Description 

Configuration Method 

FECC(H.323) 

Enables or disables the FECC 
(H.323) protocol for far site to 

Web User Interface 

Summary of Contents for VC110













































































































































































































































































Reviews:

No comments

Related manuals for VC110

VCON HD100 Getting Started Manual preview
HD100
Brand: VCON Pages: 16
S&S Northern Merlin 1000VW+ Installation, Operating And Maintenance preview
Merlin 1000VW+
Brand: S&S Northern Pages: 9
Panasonic SC-PMX70B Operating Instructions Manual preview
SC-PMX70B
Brand: Panasonic Pages: 16
Jensen Marine MSR3012 Installation And Operation Manual preview
MSR3012
Brand: Jensen Marine Pages: 18
Bose Videobar VB1 Quick Start Manual preview
Videobar VB1
Brand: Bose Pages: 2
Magnetic Autocontrol MAGSTOP MIB 10-C090 Operating Instructions Manual preview
MAGSTOP MIB 10-C090
Brand: Magnetic Autocontrol Pages: 15
Twin-Star International Bell'O Digital BDSW-1650-BLK Manual preview
Bell'O Digital BDSW-1650-BLK
Brand: Twin-Star International Pages: 20
Roadstar HIF-9997 TR Service Manual preview
HIF-9997 TR
Brand: Roadstar Pages: 45
Danfoss Termix VVX-I-R FI - 7 Series Operating Manual preview
Termix VVX-I-R FI - 7 Series
Brand: Danfoss Pages: 32
RCA RS2050 User Manual preview
RS2050
Brand: RCA Pages: 19
Exibel KW-1011B Instruction Manual preview
KW-1011B
Brand: Exibel Pages: 32
Samsung SCM-6700 Service Manual preview
SCM-6700
Brand: Samsung Pages: 49
Samsung SCM-7270 Service Manual preview
SCM-7270
Brand: Samsung Pages: 65
Samsung MXHS9000 User Manual preview
MXHS9000
Brand: Samsung Pages: 84
Sony FH-B650 Service Manual preview
FH-B650
Brand: Sony Pages: 2
Sony HCD-441 Operating Instructions Manual preview
HCD-441
Brand: Sony Pages: 27
Sony HCD-BX2 Service Manual preview
HCD-BX2
Brand: Sony Pages: 72
Sony FH-1215CD Service Manual preview
FH-1215CD
Brand: Sony Pages: 58

Brands by name

Popular brands

Load more brands