YATO YT-85716, Original Instructions Manual, Page: 11 / 64

11
EN
O R I G I N A L I N S T R U C T I O N S
sure that mains parameters correspond with parameters indicated on vacuum cleaner’s data
plate.Prior each use, please check the condition of the device, including power cord and
plug. If any faults are found, do not use the device. Damaged cables and cords must be
replaced with new ones in a specialist workshop.The degree of protection given in the table
with technical data is ensured if the device will be connected to a socket with at least the
same degree of protection. Prior to maintenance of the device please make sure, that the
power cord plug was disconnected from the mains socket.The device should be stored in a
place inaccessible for third parties, children in particular. Also during the work please note,
that the device is out of reach of unauthorised persons, children in particular.Carry the device
using the handle, do not move the device by pulling the power cord.In case the vacuum
cleaner is used as a blower, it is forbidden to direct the hose outlet towards people and ani-
mals. Check the condition of connector on a regular basis. It is forbidden to use the vacuum
cleaner with the hose damaged.
OPERATING THE DEVICE
Preparing for operation
Check the vacuum cleaner container, empty it of waste, if necessary.
Check the fi lter condition. In case the fi lter is soiled, remove the fi lter from the vacuum cleaner cover as described in the further
part of this manual and then clean it with water. Do not use detergents for cleaning. The fi lter must be completely dry before re-
installing. If the fi lter soiling cannot be removed or a decrease in the operation capacity is observed, the fi lter should be replaced
with a new one.
CAUTION! It is forbidden to work with a vacuum cleaner without a properly installed air fi lter. This can cause damage to the vac-
uum cleaner as well as electric shock.
The vacuum cleaner base allows for mounting wheels. The axle with rear wheels must be pressed into the hooks in the housing
base so that the pins in the housing match the holes in the axis of the wheels (II).
Secure the front swivel castors by inserting the pins of the wheels into the holes in the container base (III).
Attach the caps to the rear wheels with the screws by screwing them on the inside of each wheel.
Properly mounted wheels should look like in the illustration (IV).
HEPA fi lter, which is held by a frame attached to the vacuum cleaner cover by means of pins, is located under the cover. Each of
the pins securing the frame must be rotated by a quarter of a turn and then you can completely slide the frame out of the opening
(V). After removing all the pins, it is possible to remove the frame and fi lter (VI)
The vacuum cleaner for dry work can be used together with a reusable collection bag, which makes it easier to keep the container
of the vacuum cleaner clean. It is forbidden to use the collection bag during wet work.
The collection bag inlet is equipped with a spring fastening. Squeeze and hold the fastening brackets and slide the collection
bag on the hose connection to the container so that the fastening remains on the hose connection inside the container (VII). The
collection bag has a clip that facilitates its emptying. Slide the clip on the lower edge of the collection bag so as to connect both
edges of the fabric from which the collection bag was made (VIII).
Attach the cover on the upper edge of the vacuum cleaner container so that it adheres to the entire circumference. Press the
cover against the container with the latches. Pay attention to the marked places on the cover to ensure proper tightness of the
connection (IX).
Connect the fl exible hose to the inlet. Insert the hose connection into the opening so that the notches on it match the protruding
elements of the inlet, then turn it clockwise (X). Make sure that the hose will not slide out of the opening during operation.
The vacuum cleaner pipe allows for gradual length adjustment. Slide and hold the lock button and then adjust the pipe length (XI).
Once the correct length has been set, release the lock button to lock the length setting. Slide the wider pipe end into the hose end
and the narrower end into the brush connection (XII).
In the upper part of the housing at the edge, there is an opening which is used to install an adapter allowing to store the attach-
ments not used at the time (XIII).
Select the appropriate accessory for the selected work type. The brush is designed to clean large and fl at surfaces, and a narrow
crevice tool is intended for places that cannot be reached using a wide attachment, and the adapter can be used to connect the
vacuum cleaner hose to the dust extraction opening of the power tool with which it can interoperate.