![background image](http://html1.mh-extra.com/html/yato/5436218/5436218_original-instructions-manual_907930010.webp)
10
GB
O R I G I N A L I N S T R U C T I O N S
PRODUCT CHARACTERISTICS
A demolition hammer is an ordinary power tool of II class of insulation, designed for demolition and chiselling works in natural
stone, artifi cial stone, marble etc. using work tools fi tted with a hexagonal grip. Correct, reliable and safe operation of this power
tool depends on proper operation, therefore:
Before starting the work with this product, please read this manual and keep it properly.
The supplier does not assume any liability for damages resulting from failure to follow safety regulations and recommendations
specifi ed in this manual.
EQUIPMENT
The product is supplied as complete, the packaging should include:
- demolition hammer
- chisel
- punch
TECHNICAL PARAMETERS
Parameter
Measuring unit
Value
Catalogue number
YT-82100
Rated voltage
[V~]
230
Rated frequency
[Hz]
50
Rated power
[W]
1600
Impact frequency
[min
-1
]
1900
Single impact energy
[J]
65
Weight
[kg]
15,6
Noise level
- acoustic pressure
[dB]
94 ± 3,0
- power
[dB]
105 ± 3,0
Vibration level
[m/s
2
]
14,59 ± 1,5
Insulation class
II
Protection class
IP20
Hexagonal tool chuck
[mm]
30
GENERAL SAFETY CONDITIONS
NOTE!
Get acquainted with all the instructions below. Failure to observe them may lead to an electric shock, fi re or injuries. The
notion of electric tool used in the instructions applies to all the tools which are powered with electric current, both wire tools and
wireless ones.
OBSERVE THE FOLLOWING INSTRUCTIONS
Place of work
The place of work must be properly illuminated and clean.
Disorder and poor illumination may be a cause of accidents.
Do not work with electric tools in explosive environments, or those which contain infl ammable liquids, gases or vapours.
Electric tools generate sparks, which may cause a fi re in case of contact with infl ammable gases or vapours.
Do not allow children and outsiders to the place of work.
A lack of concentration may result in a loss of control over the tool.
Electric safety
The plug of the power supply cable must fi t the mains socket. Do not modify the plug. Do not use any adapters whatso-
ever in order to adapt the plug to the socket.
Unmodifi ed plug which fi ts the socket reduces the risk of an electric shock.
Avoid contact with grounded surfaces, such as pipes, heaters and refrigerators.
Grounding of the body increases the risk
of an electric shock.
Do not expose electric tools to precipitation or humidity.
Water and humidity which gets into the electric tool increases the
risk of an electric shock.
Do not overload the power supply cable. Do not use the power supply cable in order to carry the tool or to connect and
disconnect the plug from the mains socket. Avoid contact of the power supply cable with heat, oils, sharp tools and
moving elements.
Damage to the power supply cable increases the risk of an electric shock.
In case work is realised outside closed areas, it is necessary to use extension cords designed for applications outside
Summary of Contents for 5436218
