background image

©

 

2004 Tyco Safety Products, Westminster, MA 01441 USA  All specifications were current and are subject to change without notice.

PN: 579-707

Rev. A

Introduction

The 4008/4006-9801 Expansion Power Supply (EPS) is an option module 
that installs into the main fire alarm control panel. The EPS provides two 
additional NACs, and filtered/regulated 24 VDC, alarm power.

The 3 A alarm power may be split between the two NACs and the 
0.5 A auxiliary 24 VDC power tap. Refer to the NAC ratings section of these 
instructions for circuit loading restrictions. The expansion power supply is 
mounted to the right of the main system board (MSB) at the bottom of the 
chassis, and is connected by the installer via three separate harnesses.

One EPS per system is allowed.

Figure 1, below, is an illustration of the EPS assembly.

The EPS assembly is shipped with the following:

EPS assembly (bracket with two PCBs)

Screws/washers (441-002; qty: 2)

AC harness (734-179): black/white leads

Battery harness (734-180): red/black leads

Data flex harness (166-438): flat cable 

Note: 

This document contains instructions on installing the EPS into the fire 

alarm control panel. For programming instructions, refer to the 

Front Panel 

Installing, Operating, and Programming Instructions

  (579-704 for 4006, or 

579-716 for 4008).

 Figure 1  The Expansion Power Supply

Specifications

General

System 
Compatibility

4006/4008 Fire Alarm System

Operating 
Temperature

0 to 49 degrees C
32 to 120 degrees F

Operating 
Humidity

Up to 93% relative humidity 
(non condensing)

Mounting

Dimensions

Width = 4.38 in ( 11.2 cm)
Height = 7 in (17.8 cm) 
Depth = 4 in (10.2 cm)

Power

Current 
Rating

2 A  per NAC; 3 A.alarm power 
@ 24 VDC

AC Input 
Voltage

120 V, 60Hz, 2 A max
240 V, 50 Hz, 1.5 A max

Expansion Power Supply (EPS)

 Installation Instructions

In this Document

Mounting .........................................2
Panel interconnections ...................3
NAC wiring......................................5
Auxiliary 24 V wiring .......................6
NAC ratings .................................... 7

Technical Manuals Online! - http://www.tech-man.com

Summary of Contents for 4008-9801









Reviews: