YASKAWA XGI 1000-65/65 Installation And Operation Manual Download Page 39 | Manualshive

Page: 39 / 78

YASKAWA XGI 1000-65/65 Installation And Operation Manual Download Page 39

Installation and Operation Guide SOLECTRIA XGI 1000

DOCR-070733-F (2/22/2021)

Page 39 of 78

Electrical Installation DC, Method

DANGER

Electric Shock Hazard: Components with hazardous voltage and energy will electrocute operator. Operator shall avoid
touching live components with hazardous voltage and energy.  Verify the absence of voltage  using an appropriately
rated multimeter.

Always  Wear  Proper  PPE:  The  proper  Personal  Protective  Equipment  (PPE)  must  be  worn  while  working  in  close
proximity of hazardous voltage and energy.

Conduit  Installation:  All  conduit  connections  must  be  made  in  such  a  way  as  to  maintain  the  NEMA  rate  of  the
enclosure. Failure to maintain the NEMA rating will void the warranty.

WARNING

Turn AC Switch to OFF: Verify the absence of AC voltage prior to landing any conductors.

Turn the external AC breaker OFF: Verify the absence of AC voltage prior to landing any conductors.

Open Fuse Holders: Verify the absence of DC voltage and current.

NOTICE !

Check Polarity of DC Inputs: DC inputs with the wrong polarity may cause damage to the inverter. Check for proper
polarity with a multimeter.

Use Correct Fuses: Make sure to size the fuses according to NEC requirements. If using 30 A fuses, skip every other
fuse holder – DO NOT place 30 A fuses in adjacent fuse holders.

Table 3-7 DC Electrical Installation DC, Tools Required

TOOL

DESCRIPTION

#3 PHILLIPS-HEAD TORQUE DRIVER

#3 Phillips-head torque driver, capable of 30 in/lbs

#2 PHILLIPS-HEAD TORQUE DRIVER

#2 Phillips-head torque driver, capable of 10 in/lbs

MULTIMETER

1000VDC/480VAC CAT III Multimeter

Verify that the PV conductors are completely isolated from the PV array prior to landing any conductors in the inverter.
Open the Wire Box following the instructions presented in Section 3.3.5.1 through 3.3.5.2. Open all PV fuse holders prior
to landing any conductors.

Land each PV conductor to the proper fuse holder as shown in Figure 3-22. Positive conductors are on the left and the
negative on the right. Strings should be wired and labeled in decrementing order (top to bottom). Torque connections to
25 in-lbs (2.8 N-m) with a #2 Phillips-head torque driver.

«
...
37
38
39
40
41
...
»

Summary of Contents for XGI 1000-65/65















































































Reviews:

No comments