background image

  

  

xxx

Compliance with UL Standards, EU Directives, and Other Safety Standards

Certification marks for the standards for which the product has been certified by certification bodies 
are shown on nameplate. Products that do not have the marks are not certified for the standards.

North American Safety Standards (UL)

European Directives

Note: We declared the CE Marking based on the harmonized standards in the above table.

Safety Standards

Product

Model

North American Safety Standards (UL File No.)

SERVOPACKs

SGD7S

UL 61800-5-1 (E147823), 
CSA C22.2 No.274

Product

Model

EU Directive

Harmonized Standards

SERVOPACKs

SGD7S

Machinery Directive
2006/42/EC

EN ISO13849-1: 2015

EMC Directive
2014/30/EU

EN 55011 group 1, class A
EN 61000-6-2
EN 61000-6-4
EN 61800-3 (Category C2, Second 
environment)

Low Voltage Directive
2014/35/EU

EN 50178
EN 61800-5-1

RoHS Directive
2011/65/EU

EN 50581

Direct Drive Ser-
vomotors

SGM7D

EMC Directive
2014/30/EU

EN 55011 group 1, class A
EN 61000-6-2
EN 61000-6-4
EN 61800-3 (Category C2, Second 
environment)

Low Voltage Directive
2014/35/EU

EN 60034-1
EN 60034-5

RoHS Directive
2011/65/EU

EN 50581

Product

Model

Safety Standards

Standards

SERVOPACKs

SGD7S

Safety of Machinery

EN ISO13849-1:2015
IEC 60204-1

Functional Safety

IEC 61508 series
IEC 62061
IEC 61800-5-2

EMC

IEC 61326-3-1

Summary of Contents for SGM7D-01G























































































































































































































































































































































































































































































































Reviews: