Penta KB Power KBVF 4G Series Installation And Operation Manual Download

Page: 1 / 24

INSTALLATION AND OPERATION MANUAL

KBVF 4G SERIES

Variable Frequency Drives

–

For OEM Applications

Designed for Multiple Motor Technologies

(Asynchronous, PMSM, and Others)

Chassis / IP20 and NEMA 4 / IP65 Enclosures

Variable Speed / Soft-Start AC Motor Drive

with Electronic Motor Overload Protection

Rated for 208 – 230 and 400/460 Volt 50 Hz and 60 Hz

Motors from Subfractional thru 3 HP

Operates from 115, 208/230, and 400/460 Volt 50/60 Hz AC Line Input

THIS MANUAL COVERS THE FOLLOWING KBVF 4G SERIES MODELS

Chassis / IP20 Drives:

KBVF-13, 14, 21D, 22D, 23, 23D, 24, 24D, 26D, 27, 29, 29 (1P), 42, 45, 48

NEMA 4 / IP65 Drives:

KBVF-27E, 27EF, 29E, 29EF, 29EF (1P), 42E, 42EF, 45E, 45EF, 48E, 48EF





Scan this QR Code

to View, Download,

or Print the

Online Manual

Summary of Contents for KBVF 4G Series

























Search results

Summary of Contents for KBVF 4G Series

Reviews:

Related manuals for KBVF 4G Series

Brands by name

Popular brands

Penta KB Power KBVF 4G Series, Installation And Operation Manual

Search results

Summary of Contents for KBVF 4G Series

Reviews:

Related manuals for KBVF 4G Series

Brands by name

Popular brands