YASKAWA MOTOMAN-ES200RN Instructions Manual Download Page 28

Page: 28 / 82

5.5 Alterable Operating Range

5-7

HW0482143

5.5.3

Adjustment to the Pulse Limitation of S-Axis

Apply the Instruction for NX100 Concurrent I/O Parameter (Manual No. RE-CKI-A442) as
part of reference materials for adjusting the programming pendant when modifying the range
of motion of S-Axis.
The limitation to the pulse (Pulse Soft Limit

+ 1st Axis ) : SICxG200

The limitation to the pulse (Pulse Soft Limit

- 1st Axis ) : SICxG208

* Refer to 5.5(p5-4).

Degree

∗ ±

Number

of Pulse

35109

70217

105326

140434

175543

210651

Degree

105

120

135

150

∗ ±

165

180

(Standard)

Number

of Pulse

245760

280869

315977

351086

386194

421303

Adjust both of the pulse limitation and the angle of S-axis mechanical stopper as

modifying the range of motion for machinery.

NOTE

28/71

HW0482143

Summary of Contents for MOTOMAN-ES200RN



















































































Search results

Summary of Contents for MOTOMAN-ES200RN

Reviews:

YASKAWA MOTOMAN-ES200RN, Instructions Manual, Page: 28 / 82

Search results

Summary of Contents for MOTOMAN-ES200RN

Reviews: