manualshive.com logo in svg

YASKAWA MOTOMAN-ES200RN, Instructions Manual, Page: 14 / 82

Share
Download
YASKAWA MOTOMAN-ES200RN Instructions Manual Download Page 14

2.2  Shipping Bolts and Brackets

2-3

HW0482143

2.2

Shipping Bolts and Brackets

The manipulator is provided with shipping bolts and brackets at position A and with the hexa-
gon socket head cap screws at point B. (" Fig. 2 Transporting Position ")

Fig. 3  Shipping Bolts and Brackets

• The shipping brackets are painted yellow.

Position

Bolt Type

Pcs

A

Hexagon socket head cap bolt M20  X 50 mm

(Tensile strength: 1200 N/mm

2

 or more)

8

B

Hexagon socket head cap bolt M16 

 

X 20 mm

(Tensile strength: 1200 N/mm

2

 or more)

1

Before turning ON the power, check to be sure that the shipping bolts and brackets have 
been removed. The shipping bolts and brackets then must be stored for future use, in the 
event that the robot must be moved again.

B

Shipping bolt

Rubber plate

Electrical tape painted yellow

A

Shipping bracket

Front View

Side View

NOTE

14/71

HW0482143

Summary of Contents for MOTOMAN-ES200RN



















































































Reviews:

No comments