YASKAWA JVOP-KPLCA04A Series Installation Manual Download Page 59

Page: 59 / 80

6 Keypad Operation

YASKAWA

TOEP C730600 97C LCD Keypad Installation Manual

Note:

The keypad display changes when the settings and conditions change.

A -

A1-02 [Control
Method
Selection]

settings

B -

o2-04 [Drive
Model (KVA)
Selection]

settings (2 or 3
digits)

C - Presence of

DriveWorksEZ
parameter
backup

D - Parameter

backup data is
not registered

E -

Backup data
does not contain
the date
Information

F -

Backup date

◆

Verify Keypad Parameters and Drive Parameters

This procedure makes sure that the parameter setting values that
you backed up in the keypad agree with the parameter setting
values in the drive.

Note:

•

Always stop the drive before you start to verify the parameters.

•

While you restore parameters, the drive will not accept Run commands.

Summary of Contents for JVOP-KPLCA04A Series

















































































Search results

Summary of Contents for JVOP-KPLCA04A Series

Reviews:

Related manuals for JVOP-KPLCA04A Series

Brands by name

Popular brands

YASKAWA JVOP-KPLCA04A Series, Installation Manual

Search results

Summary of Contents for JVOP-KPLCA04A Series

Reviews:

Related manuals for JVOP-KPLCA04A Series

Brands by name

Popular brands