background image

5  Installation Procedure

24

 

YASKAWA

 TOBP C730600 29C YASKAWA AC Drive-Option LCD Operator Installation Manual

Connecting the LCD Operator Option to the Drive

This section contains instructions for connecting the LCD operator to V1000. For 

instructions on connecting the LCD operator to the other drives, see the Technical Manual of 

the drive connected to the LCD operator.
Plug the communication cable into the communication cable connector of the LCD Operator 

Option and the drive communications port as shown in 

Figure 11

. Ensure both cable ends 

are firmly connected. 

Refer to Item Names and Part Numbers (Sold Separately) on 

page 12

 for information regarding recommended cables.

Refer to 

Table 1

 for Built-in LED Display Behavior with a Connected LCD Operator 

Option.

Note:

Use only Yaskawa recommended cables. Using a cable not specified may cause the LCD 

Operator or drive to malfunction.

Note:

The STOP key on the drives built-in LED operator is the only functional key on the built-in LED 

operator when the LCD Operator Option is connected to the drive and parameter b1-02 is set to 

0 (LCD Operator Option). To disable the STOP key, set parameter o2-02 (STOP key Function 

Selection) to 0 (Disable).

Figure 11

Figure 11  Communication Cable Connection

STOP

V1000

(Hz)

(Hz)
(A)
(V)

:
:
:
:
:
:
:
:
:
:

周波数指令
正転逆転選択
出力周波数
出力電流
出力電圧
モニタ
ベリファイ
セットアップ
パラメータ設定
オートチューニング

据え付け、運転の前には必ず取扱説明書を読むこと。
通電中および電源遮断後

5

分以内はフロントカバーを

外さないこと。

400V

級インバータの場合は、電源の中性点が接地

されていることを確認すること。(  対応)

けが、感電のおそれがあります。

危 険

Read manual before installing.
Wait 5 minutes for capacitor discharge after
disconnecting power supply.
To conform to         requirements, make sure
to ground the supply neutral for 400V class.

Risk of electric shock.

WARNING

MODEL:JVOP-180

ޓޓޓ

            REV:A

PASSED

L/N       :BY1-00004            PRG:0100

S / N  : J007XE273710001

YASKAWA ELECTRIC CORPORATION   

MADE IN JAPAN

Comm Port

LED
Operator

Communication Cable Connector

LCD Operator Option

Drive

Summary of Contents for JVOP-180







































Reviews: