manualshive.com logo in svg

YASKAWA E-7S SERVOPACK SGD7S, Product Manual

Share
Download
YASKAWA E-7S SERVOPACK SGD7S Product Manual Download Page 406

12.3  Origin Settings

 12.3.2  When Using an Incremental Encoder

12-7

12

Settings for the INDEXER Module

When using the linear type coordinate (PnB20 = 0000h), set the calculated value in PnB25.

When using a rotary type coordinate (PnB20 

≠

 0000h), set the results in PnB25 after perform-

ing the following calculations so that the following relationships are satisfied: PnB23 

≤

 PnB25 

≤

 

PnB21.

•

If the results is smaller than PnB23 (the starting point of the rotational coordinates), add the 
width of the coordinates (PnB21 

−

 PnB23 + 1).

•

If the results is larger than PnB21 (the end point of the rotational coordinates), subtract the 
width of the coordinates (PnB21 

−

 PnB23 + 1).

Refer to the following section for information on setting up an absolute encoder.

5.15 Resetting the Absolute Encoder

 on page 5-47

12.3.2

When Using an Incremental Encoder

If you use an incremental encoder, you must set the origin every time the power supply to the 
equipment is turned ON.

Homing is used to define the machine origin. Refer to the following section for details on hom-
ing.

13.2 Homing

 on page 13-4

The setting of PnB25 is set as the current value when the power supply is turned ON or when 
homing is completed.

*

If you set PnB54 to 1 (Enable Expansion Mode), the range will be -1,073,741,823 to +1,073,741,823. Refer to the 
following section for details.

12.4 Speed/Position Expansion Function Setting

 on page 12-8

You must define the origin again if you change the settings of any of the following parameters: 
Pn20E, Pn210, Pn205, PnB20, or PnB25. Always turn the power supply OFF and ON again 
before you set the origin to enable changes to these parameters.

Important

PnB25

•

When using an incremental encoder: Origin

•

When using an absolute encoder: Absolute Encoder Offset

Setting Range

Setting Unit

Default Setting

When Enabled

Classification

-99,999,999 to 

99,999,999

*

1 reference unit

0

After restart

Setup

WARNING

If you are using an incremental encoder, always perform homing before you start program 
table operation. If you perform program table operation without performing homing, posi-
tions cannot be managed so correct positioning may not be possible.

Unexpected machine operation, failure, or personal injury may occur.

Summary of Contents for E-7S SERVOPACK SGD7S
































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands