YASKAWA AC Drive V1000 Option SI-EM3/V Installation Manual Download Page 15 | Manualshive

Page: 15 / 51

background image

4 Option Components

YASKAWA ELECTRIC

TOBP C730600 59B V1000 Option SI-EM3/V Installation Manual

15

Table 3 Male, 8-way Ethernet Modular Connector (Customer Supplied)

Male Ethernet 8-Way Modular Connector

Pin

Description

1 (Pair 2)

Transmit data (TXD) +

2 (Pair 2)

Transmit data (TXD) -

3 (Pair 3)

Receive data (RXD) +

4 (Pair 1)

Not used

<1> Not used for 10 Mbps and 100 Mbps networks.

5 (Pair 1)

Not used

6 (Pair 3)

Receive data (RXD) -

7 (Pair 4)

Not used

8 (Pair 4)

Not used

«
...
13
14
15
16
17
...
»

Summary of Contents for AC Drive V1000 Option SI-EM3/V




















































Reviews:

No comments

Related manuals for AC Drive V1000 Option SI-EM3/V

Brand: GE Pages: 425

Brand: Canarm Pages: 3

Brand: PUTCO Pages: 2

Waukesha Cherry-Burrell D4 Series

Brand: SPX FLOW Pages: 34

Brand: Planar Pages: 162

Brand: THK Pages: 134

Brand: Water Specialist Pages: 60

Brand: aerl Pages: 27

Brand: M-Elec Pages: 2

ACTPRO PRODUCT RANGE

Brand: ACT Pages: 8

Brand: Oasis Pages: 12

PMC 1204 Series

Brand: Curtis Pages: 56

Brand: Arctic King Pages: 26

Brand: Beckhoff Pages: 38

ELVOX KLYS ENM1

Brand: Vimar Pages: 24

Brand: P&B Pages: 38

Brand: MDT Pages: 51

Brand: Sennheiser Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands