background image

 
 

15 

  

  
 
 
 
 

Some of the following symbols may be used on this product. Please study them and learn their 

meaning. Proper interpretation of these symbols will allow you to operate the product better and safer. 
 

SYMBOL

 

NAME

 

DESIGNATION/EXPLANATION

 

V Volts 

Voltage 

A Amperes 

Current 

Hz 

Hertz 

Frequency (cycles per second) 

W Watts 

Power 

min Minutes 

Time 

 

Alternating Current 

Type of current 

 

Direct Current 

Type or a characteristic of current 

 

Class II Construction 

Double-insulated construction 

 

No Load Speed 

Rational speed, at no load 

/min

 

Per Minute 

Revolutions, strokes, surface speed, orbits etc.,  
per minute 

 

Wet Conditions Alert 

Do not expose to rain or use in damp locations 

 

Read The Operator’s Manual 

To reduce the risk of injury user must read and 
understand operator’s manual before using this 
product. 

 

 

Eye Protection 

Wear eye protection when operating this 
equipment. 

 

Safety Alert 

Precautions that involve your safety. 

 

Long Hair 

Failure to keep long hair away from the air inlet could 
result in personal injury. 

 

Loose Clothing 

Failure to keep loose clothing from being drawn into 
air intake could result in personal injury. 

 

Keep Bystanders Away 

Keep all bystanders at least 50 ft. away. 

 

  

 

 

SAVE THESE INSTRUCTIONS

 

Symbols

 

Summary of Contents for 060-2279-2


















Reviews: