background image

 
 

14 

  

 
 
 
 
 

If your device is not operating properly, follow the instructions below. If this 
does not solve the problem, please contact your local repair agent.

 

 
 

 

WARNING! 

Before proceeding, switch off and unplug. 
 
Tool runs slowly

 

• Check that the spool housing can rotate freely. Carefully clean it if necessary. 
• Check that the cutting line does not protrude more than 11cm from the spool housing. If it 

does, cut it off so that it just reaches the line trimming blade. 
 

Automatic line feed does not work. 
 

• Press the tabs and remove the spool cover from the housing. 
• Pull the cutting line until it protrudes 11cm from the housing. If insufficient cutting line is left on the spool, 

install a new spool of cutting line as instructed above. 

• Align the tabs on the spool cover with the cut outs in the housing. 
• Push the cover onto the housing until it snaps securely into place. 
• If the cutting line protrudes beyond the trimming blade, cut it off so that it just reaches the blade. 
• If the automatic line feed still does not work or the spool is jammed, try the following suggestion: 
• Carefully clean the spool cover and housing. 
• Remove the spool and check if the lever can move freely. 
• Remove the spool and unwind the cutting line, then wind it on neatly again as describe above. Replace the 

spool as instructed. 

 

 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Troubleshooting

 

Summary of Contents for 060-2279-2


















Reviews: