background image

This unit is a gasoline engine driven snow blower. It is 
perfect for tackling heavy snowfall — easily able to cut 
through snow in excess of a foot or more. It is easy and 
safe to operate. With proper use and care, it should give 
you many years of dependable service.

Carefully read through this entire operator's manual 
before using your new unit. Pay attention to all 
cautions and warnings.

MODEL AND SERIAL NUMBERS

Record the model and serial number as well as date 
and place of purchase for future reference. Have this 
information available when ordering parts, optional 
accessories and when making technical or warranty 
inquiries.

ENGINE MANUAL

The 

Engine Manufacturer

 is responsible for all engine-

related issues with regards to performance, power rating, 
specifications, warranty and service. Please refer to 
the 

Engine Manufacturer’s

 owner/operator’s manual, 

packed separately with your unit, for more information.

EMISSION CONTROL SYSTEM

This equipment or its engine may include exhaust and 
evaporative emission control system components 
required to meet U.S. Environmental Protection Agency 
(EPA) and/or California Air Resources Board (CARB) 
regulations. Tampering with emission controls and 
components by unauthorized personnel may result 
in severe fines or penalties. Emission controls and 
components can only be adjusted by an authorized 
engine manufacturer's service center. 

DISCLAIMER

YARDMAX reserves the right to discontinue, change, 
and improve its products at any time without notice 
or obligation to the purchaser. The descriptions and 

specifications contained in this manual were in effect at 

printing. Equipment described within this manual may be 
optional. Some illustrations may not be applicable to your 
unit.

ENVIRONMENTAL

Recycle unwanted materials instead of disposing of 
them as waste. All tools, hoses, and packaging should 
be taken to the local recycling center and disposed of 
in an environmentally safe way.

CALIFORNIA PROPOSITION 65 WARNING

Engine exhaust, some of its constituents and certain 
product components contain or emit chemicals known to 
the state of California to cause cancer and birth defects 
or other reproductive harm.  For more information, go to 

www.P65Warnings.ca.gov.

6870100010718

YB6870

Engine Displacement

:

Clearing Width:
Intake Depth:
Auger Diameter:
Impeller Diameter:
Speed:
Weight:

Manufactured in China

208 cc
26”
21”
12”
12”
6F+2R
167.5 lbs

Two-Stage Snow Blower

11~20

1~10

2018

2019

2020

1

2

3

4

5

6

7

8

9 10 11 12

21~30

Manufacture Date:

Serial Number

Model Number

2

Two-Stage Snow blower   

»   

Operator’s Manual

 

     

YB6870PM00 - 1807

Introduction    

|

Summary of Contents for YB6870





































Reviews: