background image

 

[email protected]

Note: It is critically important you start with square, solid and level footings, concrete 

pad or deck to attach your Pavilion.

We supply Post Mounts with this structure which gives you the flexibility to permanently install your structure 

to a pre-existing or new wood or concrete surface.  

• 

The hardware to attach the Post Mount to the structure is included.  

• 

The hardware to mount the structure permanently will need to be purchased separately at your local 

hardware store.

If you are mounting to concrete footers see below for the correct locations and placement.  Please double 

check for possibility of any underground utilities such as gas, telephone, cable or sprinkler lines.

Following are some examples of how to mount the structure to wood or concrete surfaces.

Refer to your local building and city codes, ordinances, neighbourhood covenants, or height restrictions 

regarding this type of structure for guidance on acceptable installation requirements.

Permanent Installation Examples

Concrete Footer 

To 

Required 

Depth

Anchoring Hardware not included

Post Mount

post to post

plinth to plinth

3

 9

'-

4

32

 13

'-2 19

32

 13

'-2

19

1 " 

2

 9'-4

 10'-2

1 4

 10'-6" 

Post to Post

Plinth to Plinth

Post to Post

Post to Post

Plinth to Plinth

9’ 3/4”

13’ 2-5/8”

10’ 6”

10’ 2-1/4”

9’ 4-1/2”

Summary of Contents for AVERY









































Reviews: