Yardistry AVERY Installation And Operating Instruction Download Page 27

Page: 27 / 40

[email protected]

Step 8: Attach Roof Panels

Part 4

Place Weather Seal on the inside of two Ridge Clip Short then place one Ridge Clip Short flush to each

side of Roof Panel Frame and 2-1/2” up from the bottom of each (420) Rafter Top, make sure not to compress

Weather Seal. Attach with three #7 x 3/4” Wood Screws per Ridge Clip Short. Ridge Clip Shorts must cover

the Roof Panels. (fig. 8.7, 8.8, 8.9 and 8.10)

Place Weather Seal on the inside of one Ridge Clip then place Ridge Clip in between both Ridge Clip

Shorts. 2-1/2” up from the bottom of (420) Rafter Tops. Ridge Clip must cover the Roof Panels. Do not

compress Weather Seal. Attach with seven #7 x 3/4” Wood Screws. (fig. 8.7, 8.8, 8.9 and 8.10)

Repeat Steps E - H for the second Roof Panel Frame.

Avery Inst 6C - Attach Roofing Trim

Fig. 8.7

Components

2 x Ridge Clip

4 x Ridge Clip Short

6 x Weather Seal

Hardware

26 x #7 x 3/4” Wood Screw

Fig. 8.8

Fig. 8.9

Weather

Seal

Weather

Seal

Ridge

Clip

Ridge

Clip

#7x 3/4” Wood Screws

(13 per Panel Frame)

Ridge

Clip Short

Ridge

Clip Short

Ridge

Clip Short

Ridge

Clip Short

Ridge

Clip

(420)

Rafter Top

(420)

Rafter Top

Fig. 8.10

Ridge

Clip

Weather

Seal

(420)

Rafter Top

Roof

Panel

2-1/2”

Summary of Contents for AVERY









































Search results

Summary of Contents for AVERY

Reviews:

Related manuals for AVERY

Brands by name

Popular brands

Yardistry AVERY, Installation And Operating Instruction

Search results

Summary of Contents for AVERY

Reviews:

Related manuals for AVERY

Brands by name

Popular brands