background image

Page    of 17 

Thank you very much for choosing this p

roduct! For future reference, please complete the owner’s record 

below: 

            Model: ___SP-38__________          Purchase Date: _______________ 

Save the receipt, warranty and these instructions. It is important that you read the entire manual to 

become familiar with this product before you begin using it.   

 
This product is designed for certain applications only.  The manufacturer cannot be responsible for 
issues arising from modification. We strongly recommend this product not be modified and/or used 
for any application other than that for which it was designed. If you have any questions relative to a 
particular  application,  DO  NOT  use  the  product  until  you  have  first  contacted  us  to  determine  if  it 
can or should be performed on the product. 
 
For technical questions please call 

1-952-938-5222

 

TECHNICAL SPECIFICATIONS 

 

Item 

Description 

Hopper Capacity 

12 Cubic Feet 

Tires 

10” x 1.75” Poly 

Working Path Width 

38”   

Maximum MPH   

 

GENERAL SAFETY RULES 

WARNING:

  Read  and  understand  all  instructions.

  Failure  to  follow  all  instructions  listed 

below may result in serious injury. 

 

CAUTION:

  Do  not  allow  persons  to  operate  or  assemble  this  sweeper

 

until  they  have 

read this manual and have developed a thorough understanding of how the sweeper

 

works.

 

 

WARNING:

  The  warnings,  cautions,  and  instructions  discussed  in  this  instruction 

manual cannot cover all possible conditions or situations that could occur. 

It must be understood 

by the operator that common sense and caution are factors which cannot be built into this product, but 

must be supplied by the operator. 

 

 

SAVE THESE INSTRUCTIONS 

 

 

Summary of Contents for SP-38


















Reviews: