background image

19

CLAMP

FUEL FILTER

CLAMP

Fig. 20

MAINTENANCE

IN-LINE FUEL FILTER  (See Fig. 20)

The fuel filter should be replaced once each season.  If fuel 

filter becomes clogged, ob struct ing fuel flow to car bu re tor, 

re place ment is re quired.
•  With engine cool, remove filter and plug fuel line sec-

 tions.

•  Place new fuel filter in position in fuel line with arrow 

pointing towards carburetor.

•  Be sure there are no fuel line leaks and clamps are 

properly positioned.

•  Immediately wipe up any spilled gasoline.

AIR FILTER 

Your engine will not run properly using a dirty air filter. 

Service air cleaner more often under dusty conditions. 

See engine manual.

MUFFLER   

Inspect and replace corroded muffler and spark arrester (if 

equipped) as it could create a fire hazard and/or damage.

ENGINE COOLING SYSTEM

To ensure proper cooling, make sure the grass screen, 

cooling fins, and other external surfaces of the engine are 

kept clean at all times.
Every 100 hours of operation (more often under extremely 

dusty, dirty conditions), remove the blower housing and 

other cooling shrouds. Clean the cooling fins and external 

surfaces as necessary. Ensure the cooling shrouds are 

reinstalled.

NOTE:

 Operating the engine with a blocked grass screen, 

dirty or plugged cooling fins, and/or cooling shrouds re moved 

will cause engine damage due to overheating.

CLEAN AIR SCREEN

The air screen is over the air intake blower located on top 

of engine.  The air screen must be kept free of dirt and 

chaff to prevent engine dam age from overheating.  Clean 

with a wire brush or compressed air to re move dirt and 

stubborn dried gum fibers.

Fig. 21

• 

Keep finished surfaces and wheels free of all gasoline, 

oil, etc.

•  Protect painted surfaces with automotive type wax.
Except for the washout port (if equipped), we do not 

recommend using a garden hose or pressure washer to 

clean the outside of your tractor unless the engine and 

transmission are covered to keep water out. Water in 

engine or transmission will shorten the useful life of your 

tractor.  Use compressed air or a leaf blower to remove 

grass, leaves and trash from outside tractor and mower.

CLEANING (See Fig. 21)

•  Clean engine, battery, seat, finish, etc. of all  foreign 

matter.

•  Clean debris from steering plate.  Debris can restrict 

clutch/brake pedal shaft movement, causing belt slip 

and loss of drive.

CAUTION:  

Avoid all pinch points and 

movable parts.

CLUTCH/BRAKE PEDAL

STEERING 

PLATE

STEERING SYSTEM, DASH, FENDER AND MOWER NOT SHOWN

CLEAN 

TOP SIDE

Summary of Contents for YP18KH38

































Reviews: