background image

12

Fig. 12

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing 

switch.  Any attempt by the operator to leave the seat with 

the engine running and the attachment clutch engaged will 

shut off the engine. You must remain fully and centrally 

positioned in the seat to prevent the engine from hesitat-

ing or cutting off when operating your equipment on rough, 

rolling terrain or hills.
• 

Select desired height of cut (see "TO ADJUST MOWER 

CUTTING HEIGHT")

•  Start mower blades by engaging at tach ment clutch 

control.

CAUTION:  Do not operate the mower 

without either the en tire grass catcher, on 

mowers so equipped, or the deflector shield 

(S) in place (See Fig. 12).

TO STOP MOWER BLADES

Disengage at tach ment clutch con trol.

OPERATION

TO ADJUST GAUGE WHEELS (See Fig. 11)

Gauge wheels  are properly adjusted when they are slightly 

off the ground when mower is at the desired cutting height 

in operating position. Gauge wheels then keep the deck 

in proper position to help prevent scalping in most terrain 

conditions. 

NOTE:

Adjust gauge wheels with tractor on a flat level 

surface.
•  Adjust mower to desired cutting height (See “TO AD-

 JUST MOWER CUT TING HEIGHT” in the Operation 

sec tion of this manual).

•  With mower in desired height of cut po si tion, gauge 

wheels should be assembled so they are slightly off 

the ground. In stall gauge wheel in appropriate hole as 

shown and tighten se cure ly.

• 

Repeat for opposite side installing gauge wheel in same 

adjustment hole.

Fig. 11

A

TO ADJUST MOWER CUTTING HEIGHT 

(See Fig. 10)

The position of the attachment lift lever (A) determines the 

cutting height.

•  Put attachment lift lever in desired cutting height slot.
The cutting height range is ap prox i mate ly 1 to 4" (25,4 to 

101,6 mm). The heights are measured from the ground to 

the blade tip with the engine not running. These heights are 

approximate and may vary depending upon soil conditions, 

height of grass and types of grass being mowed.
•  The average lawn should be cut to approximately 

2-1/2" (63,5 mm) during the cool season and to over 3" 

(76,2 mm) during hot months. For healthier and better 

looking lawns, mow often and after moderate growth.

•  For best cutting performance, grass over 6" (152,4 mm) 

in height should be mowed twice. Make the first cut 

relatively high; the second to de sired height.

Fig. 10

Fig. 9

TO MOVE FORWARD AND BACKWARD  

(See Fig.9)

The direction and speed of movement is controlled by the 

forward and reverse drive pedals.
•  Start tractor and release parking brake.
• 

Slowly depress forward (K) or reverse (L) drive pedal to 

begin movement. Ground speed increases the further 

down the pedal is depressed.

K

L

Summary of Contents for YP18KH38

































Reviews: