background image

7

Discharge Chute 

The angle of the discharge chute controls the distance 
that the snow is thrown. Tilt the discharge chute up for 
greater distance; tilt down for less distance. Loosen the 
hand knob on the side of the discharge chute to adjust. 
Tilt the chute to the desired position, and tighten the 
knob.

Choke Lever 

The location of the choke lever is indicated in Figure 5 
inset. You will have to use this lever to start the engine. 
Push the lever all the way up to the FULL/ON position, 
or all the way down to the OFF position as desired.

Primer Button

Used to inject fuel directly into the carburetor to insure 
fast starts in cold weather. Follow engine manual to 
prime engine.

Ignition Key 

Used to start engine. Put key  in “ON” position to start 
for both electric and recoil start engines. Follow starting 
instructions given in the next section.

Recoil Starter 

Used to manually start the engine.

Electric Starter 

(If equipped)

 

Used to start engine with a 120V power source

Plug for Electric Start 

(If equipped)

 

Requires use of a three-prong outdoor extension cord

and a 120V power source

Spark Plug Access

Spark plug located under the access cover.

SECTION 4:  OPERATING YOUR SNOW THROWER

Before Starting

The spark plug wire was disconnected for safety. 
Attach spark plug wire to spark plug before starting.

Gas and Oil Fill-Up 

Check oil and gasoline level and add if necessary. 
Follow related instructions in the seperate engine 
manual packed with your snow thrower. 

To Start Engine 

Insert ignition key into slot. Turn key to ON position

.

Now follow the instructions below as it pertains to 
your unit.

Electric Starter 

 (If equipped)

Figure 6

The electric starter is equipped with a grounded 
three-wire power cord and plug, and is designed to 
operate on 120 volt AC household current.

Determine that your house wiring is a three-wire 
grounded system. Ask a licensed electrician if you 
are not certain. 

If your home wiring system is not a three-wire 
grounded system,

 do not use this electric starter 

under any conditions. 

If your home electrical system is grounded,

 but 

a three-hole receptacle is not available, one should 
be installed by a licensed electrician before using 
the electric starter.

WARNING: 

Read, understand, and follow all 

instructions and warnings on the machine and 
in this manual before operating.

WARNING: 

Use extreme care when 

handling gasoline. Gasoline is extremely 
flammable and the vapors are explosive. Never 
fuel the machine indoors or while the engine is 
hot or running. Extinguish cigarettes, cigars, 
pipes and other sources of ignition.

WARNING: 

The electric starter must be 

used with a properly grounded three-prong 
receptacle at all times to avoid the possibility of 
electric shock. Follow all instructions carefully 
prior to operating the electric starter.

Press auger
control handle
to engage 
auger

Turn handle 
to change 
discharge
direction 

Recoil 

Starter

Electric

Starter* 

Key

Spark Plug Access

Primer

Choke

Lever

* If equipped

Summary of Contents for 285





























Reviews: